manualshive.com logo in svg

Olivetti PR2 PLUS, Руководство по обслуживанию, Страница: 102 / 172

Поделиться
Скачать
Olivetti PR2 PLUS Скачать руководство пользователя страница 102

5-18

   Service Manual

XZAC4219-05

X

X

X

Paper photosensor 
not adjusted correctly 

See 

“Adjusting Paper Photosensor” on 

page 6 - 8

X

X

Print bar not adjusted 
correctly 

See 

“Adjusting the roller gears” on page 6 

- 9

X

X

Wrong configuration 
parameters 

Reprogram the parameters of the printer. 
See  

“Modifying configuration parameters” 

on page 4 - 2

X

Document driving 
belt not correctly 
adjusted 

See  

“Adjusting the document drive belt” 

on page 6 - 3

X

Band not adjusted

Adjust the printing band. See  

“Adjusting 

the roller gears” on page 6 - 9

X

Roller gears not 
adjusted 

Adjust the gears. See  

“Adjusting the roller 

gears” on page 6 - 9

X

Front pressure rollers 
not adjusted 
correctly. 

 Adjust the pressers of the front rollers.  

“Adjusting the front pressure rollers” on 
page 6 - 10

X

X

Carriage belt not 
calibrated

Adjust the belt for carriage movement. See 

“Replacement and adjustment of belt for 
carriage movement” on page 6 - 15

X

X

Rear roller motor not 
working

Replace the motor. See  

“Disassembling/

reassembling pressure roller unit” on 
page 7 - 20

Fault

Possible cause

Solution

The machine does

not swi

tch 

on

The machine does not 

c

onnect w

ith the

 sy

stem

The

 sel

f-test indic

a

tes a 

fault on the Motherboar

d

The

 sel

f-text indic

a

tes an

e

rror i

n

 the 

mechani

c

s

The machine does

not swi

tch 

on

The machine does not 

c

onnect w

ith the

 sy

stem

Содержание PR2 PLUS













































































































































































Отзывы:

Нет отзывов