manualshive.com logo in svg

Olivetti JS-504, Руководство по обслуживанию, Страница: 21 / 32

Поделиться
Скачать
Olivetti JS-504 Скачать руководство пользователя страница 21

5. Sensor check

Field Service Ver. 1.0 Aug. 2007

16

JS-504

Adjustment / Setting

5.

Sensor check

5.1

Check procedure

A. Procedure

1.

Call the Service Mode to the screen.

See P.434 of the main body service manual.

2.

Touch [State Confirmation].

3.

Touch [Sensor Check].

4.

Touch ten times [

z

].

5.1.1

Sensor check screen

• This is only typical screen which may be different from what are shown on each individ-

ual main body.

5.1.2

Sensor check list

A0D5F3E501DA

Symbol

Panel display

Part/Signal name

Operation characteristics/

panel display

1

0

PS1

Exit (Non-sort1)

Lower tray exit sensor

Paper 

present

Paper not 

present

PS2

Exit (Non-sort2)

Upper tray exit sensor

Paper 

present

Paper not 

present

T1FDTB/LED Full (Non-sort1)

Lower tray paper full detect 
board/LED

Full

Other than 

full

T2FDTB/LED Full (Non-sort2)

Upper tray paper full detect 
board/LED

Full

Other than 

full

PS3

Front cover

Front door sensor

Closed

Open

PS4

Route change home

Route change home sensor

Blocked

Unblocked

PS6

Home(Shift)

Shift home sensor

Blocked

Unblocked

Service Manual                           

 

            Y109311

-

7

Содержание JS-504

































Отзывы:

Нет отзывов