manualshive.com logo in svg

Olivetti IC-420, Руководство по обслуживанию, Страница: 58 / 61

Поделиться
Скачать
Olivetti IC-420 Скачать руководство пользователя страница 58

Specifications

The Fiery ES has, or makes use of, the following features.

Hardware features

•

2.4GHz AMD Quad Core GX-424CC

•

2 x 2GB DIMM (4GB total)

•

Hard disk drive (500GB)

•

Printer interface board

•

2 USB2.0 ports, 

•

2 USB3.0 ports

•

10BaseT/100BaseTX/1000BaseT network port for network printing

•

10BaseT/100BaseTX/1000BaseT printer port for a Ethernet cable to the printer

•

3V manganese dioxide lithium coin cell battery (Panasonic CR2032 or equivalent)

•

Power button

Physical specifications 

•

Operating Environment:

Temperature: 0

°

C to +40

°

C

Relative Humidity: 10%-85% (non-condensing)

•

Power Supply Rating: 100 -240V, 50-60Hz, 2-4A

•

Power Consumption: 20W (typical)

•

Dimensions (Depth 

x

 Width 

x

 Height): 

5.8 cm (2.3 in.) 

x

 19.5 cm (7.7 in.) 

x

 19.5 cm (7.7 in.)

•

Weight: 1.4 kg (3.0 lb.)

Networking and connectivity 

The Fiery ES has the following networking features:

•

Supports AppleTalk and TCP/IP protocols simultaneously

•

RJ-45 Ethernet LAN port for twisted pair (10BaseT/100BaseTX/1000BaseT) network connection

Service Guide

Y119660-9

Содержание IC-420






























































Отзывы:

Нет отзывов