Olivetti DP-670 Скачать руководство пользователя страница 46

Страница: 46 / 103

3K5

1-3-26

U203

Checking DP operation
Description

Simulates the original conveying operation separately in the DP.

Purpose

To check the DP operation.

Method

1. Press the start key.
2. Place an original in the DP if running this simulation with paper.
3. Select the item to be operated.
4. When selecting [ADF] or [RADF], to set the magnification using the cursor up/down keys.

5. Press the start key. The operation starts.
6. To stop continuous operation, press the stop/clear key.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U243

Checking the operation of the DP motors
Description

Turns the motors and solenoids in the DP on.

Purpose

To check the operation of the DP motors or solenoids.

Method

1. Press the start key.
2. Select the item to be operated.
3. Press the start key. The operation starts.

4. To stop operation, press the stop/clear key.

Completion

Press the stop/clear key when operation stops. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Operation

Setting range

Initial setting

ADF

With paper, single-sided original

100 to 200 (%)

100

RADF

With paper, double-sided original

100 to 200 (%)

100

ADF (NON P)

Without paper, single-sided original
(continuous operation)

RADF (NON P)

Without paper, double-sided original
(continuous operation)

Display

Motors and solenoids

DP FEED MOTOR

Original feed motor (OFM) is turned on.

DP CONV MOTOR

Original conveying motor (OCM) is turned on.

DP REV MOTOR

Original switchback motor (OSBM) is turned on.

DP RJ SOL

Switchback feedshift solenoid (SBFSSOL) is turned on.

DP RP SOL

Switchback pressure solenoid (SBPSOL) is turned on.

Service Manual Y108671-9

Содержание DP-670







































































































Результаты поиска

Содержание DP-670

Отзывы:

Похожие инструкции для DP-670

Бренды по названию

Популярные бренды

Olivetti DP-670, Руководство по обслуживанию

Результаты поиска

Содержание DP-670

Отзывы:

Похожие инструкции для DP-670

Бренды по названию

Популярные бренды