Olivetti DP-670 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 103

background image

3K5-2

1-3-25

U074

Adjusting the DP input light luminosity
Description

Sets the luminosity correction for scanning originals from the DP.

Purpose

Used if the exposure amount differs significantly between when scanning an original on the platen and when
scanning an original from the DP.

Setting

1. Press the start key.
2. Select the item to be set.

3. Change the setting using the cursor up/down keys.

Increasing the setting makes the luminosity higher, and decreasing it makes the luminosity lower.

4. Press the start key. The value is set.

Supplement

While this maintenance item is being executed, copying from an original is available in the interrupt copying
mode.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U087

Setting DP reading position modification operation
Description

The presence or absence of dust is determined by comparing the scan data of the original trailing edge and
that taken after the original is conveyed past the DP original scanning position. If dust is identified, the DP
original scanning position is adjusted for the following originals.

Purpose

When using DP, to solve the problem when black lines occurs due to the dust with respect to original reading
position.

Method

1. Press the start key.
2. Select the item.

Setting: Standard data when dust is detected

1. Change the value using the cursor up/down keys.
2. Press the start key. The value is set.

Setting: Initialization of original reading position

1. Select [CLEAR].
2. Press the start key. The setting is cleared.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Description

Setting range

Initial setting

DP input light luminosity

-12 to 12

0

Display

Description

Setting
range

Initial set-
ting

CCD

Setting of standard data when dust is detected.

10 to 95

35

BLACK LINE

Initialization of original reading position.

-

-

Y108671-9 Service Manual

«
...
43
44
45
46
47
...
»

Содержание DP-670








































































































Отзывы:

Нет отзывов

Похожие инструкции для DP-670

Бренд: Lanier Страницы: 252

Бренд: Olivetti Страницы: 656

imageRUNNER 1600

Бренд: Canon Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды