Olivetti d-Copia 283MF plus Скачать руководство пользователя страница 18

Страница: 18 / 187

Part Names and Functions

1-2

OPERATION GUIDE

Operation Panel

For the names of keys and indicators required when functions other than FAX are used, refer to the machine’s

Operation Guide

Blinks while

data is sending/

receiving.

Message Display. Check what is shown

here while operating the machine.

Blinks during printing

operation.

Selects the menu displayed

at the lower left in the

Message Display.

Selects the menu displayed

at the lower right in the

Message Display.

Switches between on-hook and off-hook when

manually sending a FAX.

Shifts to switch the one-touch key numbers

(1 to 11 and 12 to 22).

Lamp is lit while shifted (12 to 22).

Displays the Add Destination screen, where you can add

destinations.

Displays the Confirm Destination screen, where you can edit and delete

destinations.

Calls the previous destination. Also used to enter a

pause when entering a FAX number.

Displays the Address Book screen, where you can add, edit and delete destinations.

Used to call destinations registered to

the one-touch key numbers (1 to 22).

Displays the

Copy screen.

Displays the FAX screen.

Displays the Send screen.

Displays the Document Box screen.

Displays the Status/Job Cancel screen.

Displays the System Menu/Counter

menu screen.

Содержание d-Copia 283MF plus




























































































































































































Результаты поиска

Содержание d-Copia 283MF plus

Отзывы:

Похожие инструкции для d-Copia 283MF plus

Бренды по названию

Популярные бренды

Olivetti d-Copia 283MF plus, Руководство по эксплуатации

Результаты поиска

Содержание d-Copia 283MF plus

Отзывы:

Похожие инструкции для d-Copia 283MF plus

Бренды по названию

Популярные бренды