Olivetti d-Copia 1801MF Plus страница 192 Скачать руководство пользователя | Manualshive

Страница: 192 / 492

background image

2NC/2NF/2NG/2NN/3P7/3P8/3P9

1-4-20

(2) Self diagnostic codes

If the part causing the problem was not supplied, use the unit including the part for replacement

Caution:

Before attempting to check the power supply and the fuser unit, be sure to turn the power switch off and
unplug the machine from power. Allow at least 5 seconds before starting to conduct service until the capaci-
tors on the circuit boards have been completely discharged.
To reset a service call regarding the Maintenance T display and the DP, performing U906 Disconnection at
Defect is required. (See page 1-3-114)
.

Code

Contents

Related parts

Check procedures/

corrective measures

0030

FAX control PWB system
error

Processing with the fax soft-
ware was disabled due to a
software problem.

FAX control PWB

1. Turn the main power swtch off and after

5 seconds, re-mount the FAX controller
PWB, then turn power on.

2. Reinstall the fax software.
3. Replace the FAX control PWB.

0060

Main/Engine PWB mis-
match

Unmatching engine and
engine sub boards.
Defective engine subboard

Main/Engine PWB

1. Turn the main power swtch off and after

5 seconds, then turn power on.

2. Replace the main/engine PWB (see

0100

Backup memory device
error

EEPROM
(Main/Engine
PWB)

1. Turn the main power swtch off and after

5 seconds, then turn power on.

2. Check that the EEPROM on the main

circuit PWB is peroperly installed on the
main circuit PWB and, if not, re-install it.

3. Replace the main/engine PWB (see

0120

MAC address data error

For data in which the MAC
address is invalid.

EEPROM
(Main/Engine
PWB)

1. Turn the main power swtch off and after

5 seconds, then turn power on.

2. Check the MAC address on the network

status page.

3. If it is blank, obtain an EEPROM with its

MAC address written from the service
support and install.

4. Replace the main/engine PWB (see

«
...
190
191
192
193
194
...
»

Содержание d-Copia 1801MF Plus













































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для d-Copia 1801MF Plus

Бренд: QMS Страницы: 122

Бренд: QMS Страницы: 306

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Magicard Страницы: 124

Бренд: Keithley Страницы: 97

Бренд: Printekmobile Страницы: 2

Бренд: Kimo Страницы: 2

Бренд: Olivetti Страницы: 97

Бренд: Digital Equipment Страницы: 122

Бренд: Xerox Страницы: 6

Бренд: Oki Страницы: 76

Бренд: SNBC Страницы: 52

Бренд: WOOSIM Страницы: 20

Бренд: DataCard Страницы: 5

Бренд: CAB Страницы: 222

Бренд: SATO Страницы: 36

Бренд: Olivetti Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды