Olivetti d-Color MF2613En Скачать руководство пользователя страница 87

Страница: 87 / 375

2PV/2PW-3

1-3-49

U601

Initializing permanent data

Description

Initializes software switches on the FAX control PWB according to the destination and OEM.

Purpose

To initialize the FAX control PWB without changing user registration data.

Method

1. Press the start key.
2. Select [Country Code] and enter a destination code using the numeric keys (refer to the des-

tination code list on following for the destination code).

* : OEM code is no operation necessary.

3. Select [Execute] and press the start key. Data initialization starts. To cancel data initialization,

press the stop key.

4. After data initialization, the entered destination, OEM codes and ROM version are displayed.

A ROM version displays three kinds, application, boot, and IPL.

U603

Setting user data 1

Description

Makes user settings to enable the use of the machine as a fax.

Purpose

To be executed as required.

Method

1. Press the start key.
2. Select [Line Type] and press the start key.
3. Select the setting using the cursor up/down keys.

* : Initial setting: DTMF

4. Press the start key. The setting is set.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Display

Description

DTMF

10PPS

10 PPS

20PPS

20 PPS

Service Manual

Y116650-5

Содержание d-Color MF2613En























































































































































































































































































































































































Результаты поиска

Содержание d-Color MF2613En

Отзывы:

Похожие инструкции для d-Color MF2613En

Бренды по названию

Популярные бренды

Olivetti d-Color MF2613En, Руководство по обслуживанию

Результаты поиска

Содержание d-Color MF2613En

Отзывы:

Похожие инструкции для d-Color MF2613En

Бренды по названию

Популярные бренды