Olivetti d-Color MF2613En Скачать руководство пользователя страница 107

Страница: 107 / 375

2PV/2PW

1-3-69

U660

Setting the NCU

Description

Makes setting regarding the network control unit (NCU).

Purpose

To be executed as required.

Method

1. Press the start key.
2. Select the item to be set using the cursor up/down keys.

Setting the connection to PBX/PSTN

Selects if a fax is to be connected to either a PBX or public switched telephone network.

1. Select the setting using the cursor up/down keys.

* : Initial setting: PSTN

2. Press the start key. The setting is set.

Setting PSTN dial tone detection

Selects if the dial tone is detected to check the telephone is off the hook when a fax is connected
to a public switched telephone network.

1. Select the setting using the cursor up/down keys.

* : Initial setting: On

2. Press the start key. The setting is set.

Item No.

Description

Display

Description

Exchange

Sets the connection to PBX/PSTN.

Dial Tone

Sets PSTN dial tone detection.

Busy Tone

Sets busy tone detection.

PBX Setting

Setting for a PBX.

DC Loop

Sets the loop current detection before dialing.

Display

Description

PSTN

Connected to the public switched telephone network.

PBX

Connected to a PBX.

Display

Description

Detects the dial tone.

Off

Does not detect the dial tone.

Service Manual

Y116650-5

Содержание d-Color MF2613En























































































































































































































































































































































































Результаты поиска

Содержание d-Color MF2613En

Отзывы:

Похожие инструкции для d-Color MF2613En

Бренды по названию

Популярные бренды

Olivetti d-Color MF2613En, Руководство по обслуживанию

Результаты поиска

Содержание d-Color MF2613En

Отзывы:

Похожие инструкции для d-Color MF2613En

Бренды по названию

Популярные бренды