Olivetti d-Color MF2001 Скачать руководство пользователя страница 73

Страница: 73 / 333

2KZ/2K0

1-3-35

U070

2. Press the start key. The value is set.

Adjustment: [X Scan Zoom]

1. Change the setting value using the cursor left/right keys or numeric keys.

For copy example 1, increase the value. For copy example 2, decrease the value.

Figure 1-3-11

2. Press the start key. The value is set.

Caution

Check the copy image after the adjustment. If the image is still incorrect, perform the following

adjustments in maintenance mode.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Original

Copy

example 1

Copy

example 2

U070

U071

( P.1-3-36)

U404

( P.1-3-74)

Y113010-4

Sevice Manual

Содержание d-Color MF2001













































































































































































































































































































































Результаты поиска

Содержание d-Color MF2001

Отзывы:

Olivetti d-Color MF2001, Руководство по обслуживанию, Страница: 73 / 333

Результаты поиска

Содержание d-Color MF2001

Отзывы: