Olivetti d-Color MF2001 Скачать руководство пользователя страница 36

Страница: 36 / 333

2KZ/2K0

1-2-12

1. Release the hook and then remove the

switch cover.

2. Turn the cassette heater switch on.

Note:

When the cassette heater is

used, it turns it on.

3. Refit the switch cover.

Figure 1-2-19

1. Install the optional devices (Document

finisher, Fax kit, etc.) as required.

1. Connect the power cord to the connector on the machine.

2. Insert the power plug into the wall outlet.

1. Turn the main power switch on.

The machine automatically starts to feed toner in the developer unit.

Note:

When the main power switch is turned on for the first time, it takes about one minute until

entering the state that can be copied.

2. The drive chain is disengaged when toner installation is completed.

Switch the cassette heater switch

Switch cover

Hook

Install the other optional devices

Connect the power cord

Installing toner

Service Manual Y113010-4

Содержание d-Color MF2001













































































































































































































































































































































Результаты поиска

Содержание d-Color MF2001

Отзывы:

Olivetti d-Color MF2001, Руководство по обслуживанию, Страница: 36 / 333

Результаты поиска

Содержание d-Color MF2001

Отзывы: