Olivetti d-Color MF2001 Скачать руководство пользователя страница 250

Страница: 250 / 333

2KZ/2K0

2-1-5

2-1-2 Drum section

The drum section consists of the drum, the charger roller unit, and the cleaning unit, and the drum surface is

uniformly charged in preparation for formation of residual image by laser beam.

After transfer is complete, toner remaining on the drum surface is chipped off with the cleaning blade and is

collected to the waste toner box with the sweep roller. The cleaning lamp (CL) consists of LEDs and removes

residual charge on the drum before main charging.

Figure 2-1-7 Drum section

1. Drum

2. Charger roller

3. Charger cleaning roller

4. Charger case

5. Cleaning blade

6. Sweep roller

7. Drum frame

8. Cleaning lamp (CL)

Y113010-4

Sevice Manual

Содержание d-Color MF2001













































































































































































































































































































































Результаты поиска

Содержание d-Color MF2001

Отзывы:

Olivetti d-Color MF2001, Руководство по обслуживанию, Страница: 250 / 333

Результаты поиска

Содержание d-Color MF2001

Отзывы: