Olivetti d-Color MF2001 Скачать руководство пользователя страница 244

Страница: 244 / 333

2KZ/2K0

1-6-1

1-6 Requirements on PWB Replacement

1-6-1 Upgrading the firmware

Follow the procedure to upgrade the firmware below.

Preparation

Extract the file that has the download firmware and store them in a USB Memory.

NOTE:

To improve Firmware Upgrade speed, a separate SKIP file can be added to the USB Memory Stick

with the Firmware Upgrade package. The Skip file will allow ONLY the Firmware that has been

Upgraded to a New Version to load, skipping duplicate Firmware Levels.

Procedure

1. Turn ON the main power switch and

confirm if the screen shows “Ready to

print” then, turn OFF the main power

switch.

2. Insert USB memory that has the firm-

ware in the USB memory slot.

3. Turn ON the main power switch.

4. About 50 seconds later, “Farmware

Update” will be displayed (this shows

that downloading is ready to start).

5. Select the firmware to upgrade by refer-

ring to the following codes:

CTRL

→

LSU

→

ENGN

→

FAX

→

CLT1

→

CLT2

→

OPT

→

DIC

→

PANL

Figure 1-6-1

Example:

=================

Firmware Update First line: Status of upgrading.

CTRL Second line: Firm ware for upgrading.

xxx% Third line: The progress of upgrading in %.

=================

6. Confirm that upgrading is completed.

7. Confirm that the version of the firmware

is correctly displayed.

8. Turn OFF the main power switch and

remove the USB memory.

USB memory

USB memory slot

* Main PWB (CTRL)

* DP main PWB (DP)

* PF main PWB (PF)

* DF main PWB (DF)

* Bridge PWB (AK)

* Engin fuser PWB (IH)

* Engine LSU PWB (LSU)

* Engine IO PWB (IO)

* Engine PWB (ENGN)

* FAX PWB (FAX)

* First color table (CLT1)

* Second color table (CLT2)

* Language data (OPT)

* Dictionary data (DIC)

* Operation panel PWB (PANL)

Y113010-4

Sevice Manual

Содержание d-Color MF2001













































































































































































































































































































































Результаты поиска

Содержание d-Color MF2001

Отзывы:

Olivetti d-Color MF2001, Руководство по обслуживанию, Страница: 244 / 333

Результаты поиска

Содержание d-Color MF2001

Отзывы: