Olivetti d-Color MF2001 Скачать руководство пользователя страница 233

Страница: 233 / 333

2KZ/2K0

1-5-29

4. Remove all connectors from DP main

PWB.

5. Remove five clamps and then remove

the waires from holder.

6. Remove two screws and then remove

the holder.

Figure 1-5-53

7. Remove six screws and then remove

the DP main PWB.

8. Check or replace the DP main PWB

and refit all the removed parts.

CAUTION:

When replacing the DP

main PWB, remove the EEPROM from

the DP main PWB that has been

removed and then reattach it to the new

DP main PWB.

Figure 1-5-54

Clamps

Wires

Holder

Screw

DP main PWB

Screw

DP main PWB

Y113010-4

Sevice Manual

Содержание d-Color MF2001













































































































































































































































































































































Результаты поиска

Содержание d-Color MF2001

Отзывы:

Olivetti d-Color MF2001, Руководство по обслуживанию, Страница: 233 / 333

Результаты поиска

Содержание d-Color MF2001

Отзывы: