Olivetti d-Color MF2001 Скачать руководство пользователя страница 202

Страница: 202 / 333

2KZ/2K0

1-4-56

1-4-6 Send error code

This section describes the scanning errors and descriptions, preventive actions, as well as corrective actions.

Error codes not described here could fall within software errors.

If such an error is encountered, turn power off then on, and advise the service representative.

(1) Scan to SMB error codes

Code

Contents

Check procedures/corrective measures

1101

Host destined does not exist on the net-

work.

1. Confirm the destined host.

2. Confirm thedevice's network parameters.

3. Confirm the parameters of the network to which the

device is connected are correct.

1102

1. Confirm user name and password.

2. Confirm the parameters of the network to which the

device is connected are correct.

3. Check the host if the folder is properly shared.

1103

Destined host, folder, and/or file names

are invalid.

1. Check illegal characters are not contained within

these names.

2. Check the name of the folder and files conform with

the naming syntax.

3. Confirm destined host and folder.

1105

SMB protocol is not enabled.

1. Confirm device's SMB protocols.

2101

1. Confirm the destined host.

2. Confirm that the LAN cable is properly connected to

the device.

3. Check the SMB port number.

4. Confirm the device's network parameters.

5. Confirm the parameters of the network to which the

device is connected are correct.

2201

Writing scanned data has failed.

1. Check the file name to save the scanned data.

2. Confirm the device's network parameters.

3. Confirm the parameters of the network to which the

device is connected are correct.

Service Manual Y113010-4

Содержание d-Color MF2001













































































































































































































































































































































Результаты поиска

Содержание d-Color MF2001

Отзывы:

Olivetti d-Color MF2001, Руководство по обслуживанию, Страница: 202 / 333

Результаты поиска

Содержание d-Color MF2001

Отзывы: