Olimpia splendid Maestro Smart Series, Инструкция по установке, использованию и техническому обслуживанию, Страница: 15 / 23

WARNING: The power supply to the unit must comply with all local and/or national codes as may have jurisdiction. It is also required to
ensure power supply is equipped with a sufficient earth ground for the safety of the occupants as well as the well being of the electronic
controls.
WARNING: The following procedure must be performed by a qualified technician and in compliance with all local and national
codes or regulations
.
To prevent the risk of electric shock you must deenergize the unit before attempting to make electrical connections or any maintenance
operations.
To perform the electrical connections through a cable embedded into the wall, proceed as follows:

Remove the lower cover (wedged in) (fig. 17 ref. A)

Remove the upper cover (wedged in) (fig. 17 ref. B)

Unscrew the 6 screws that lock the front cover (fig. 18 ref. A)

Remove the front cover (fig. 19)

Remove the cover of the electrical box (fig. 19 ref. A)

Unscrew the cable clamp (fig. 19 ref. B)

Unscrew the cable fixing screws of the terminal strip (fig. 19 ref. C)

Remove the cable then i nsert the new cable following the same route

Remove the wooden wedge from behind the unit

L ock the cable's three poles in the terminal strip and tighten the screws (fig. 19 ref. C)

B lock the cable with the clamp (fig. 19 ref. B)

C lose the protection of the board (fig. 19 ref. A)

R efit the front cover of the unit with the six screws

R efit the two wedged-in covers (upper and lower).
CAUTION: The following procedures should be performed with the machine already positioned on the bracket. Read the instructions
carefully before completing the electric connections.
2.4 TOP/BOTTOM INSTALLATION CONFIGURATION
This unit may be installed either at the bottom of the wall (adjacent to the floor) or at the top (adjacent to the ceiling). The air jet can be
modified to optimize air distribution and occupant comfort by changing the position of the air outlet fap. Figure 20 refers to a unit configured
for installation near the floor in which air flows upwards. The same configuration may also be used to install the unit near the ceiling with the
cooling function, allowing an increase to the airflow in the room. Figure 21 refers to a unit configured for installation near the ceiling in which
air flows downwards.
THE FOLLOWING OPERATIONS MUST BE PERFORMED WHEN THE UNIT IS SWITCHED OFF AND DEENERGIZED
CHANGING THE CONFIGURATION OF THE AIR OUTLET FLAP FROM BOTTOM TO TOP OF WALL

Carefully open the air outlet flap

U nhook the flap (side and central hooks on the baffles) (fig. 20)

R emove the pin (fig. 20 ref. A)

T urn the fap 18Q° (fig. 20)

I nsert the pin (fig. 21, ref. A) on the right-hand side of the fap

I nsert the fap into the unit by inserting the pin (fig. 21 ref. B) into the top hole on the right-hand side in the opening (fig. 21 ref. C), and the
flap's left-hand hole on the upper pin that is on the left-hand side in the opening (fig. 21, ref. D)
CHANGING THE CONFIGURATION OF THE AIR OUTLET FLAP FROM TOP TO BOTTOM OF WALL

Carefully open the air outlet flap

U nhook the flap (side and central hooks on the baffles) (fig. 20)

R emove the pin (fig. 20 ref. A)

T urn the fap 18Q° (fig. 20)

I nsert the pin (fig. 21, ref. A) on the right-hand side of the fap

I nsert the fap into the unit by inserting the pin (fig. 21 ref. B) into the bottom hole on the right-hand side of the opening (fig. 21 ref. C), and
the flap's left-hand hole on the lower pin that is on the left-hand side in the opening (fig. 21, ref. D)
After having performed the steps required to change the air outlet flap position it is necessary to configure the unit’s control board by
following the instructions listed in chapter 2.5 of this manual.
IMPORTANT: FOR CORRECT UNIT OPERATION EACH TIME THE CONFIGURATION OF THE AIR OUTLET FLAP IS MODIFIED
THERE MUST BE A CORRESPONDING CHANGE TO THE CONTROL BOARD’S SETTINGS.
2
IMPORTANT:
Prior to starting the unit the two supplementary filters (green purifying filter and black active carbon filter) contained in
the parts bag must be installed. Refer to section 2.6.1, which describes how to clean the filters, to understand both how to remove
and reinstall them. Also reference figures 25, 26, and 27 as detailed in section 2.6.1.
13