Oki IP-5530 Скачать руководство пользователя страница 195 | Manualshive

Страница: 195 / 265

Oki IP-5530 Скачать руководство пользователя страница 195

195

Advanced operations

The heater temperature control system for printing

Print

Delay

time

Standby time

Set temperature maintained

Standby temperature

maintained

Temperature control stop

(Time)

Printheater set temperature

Preheater set temperature

Afterheater set temperature

Standby set temperature

Ambient temperature

(Temperature)

The Printer receives the RIP data.

The heaters are in standby at the temperatures below.
Preheater: 35 ºC
Printheater: 35 ºC
Afterheater: 35 ºC
However, the heaters temperatures above are lowered to the set temperatures if the set temperatures are lower than
the standby temperatures.

Display the heater control menu

Press the HEATER button to display the heater control menu.

2

nn

50 40 45°C

Aft 40 +40 45Pre

Heater operating

information

Afterheater

The

+

sign indicates that

the heater is heating.

Printheater

Preheater

Set temperature
Set temperature

Heater operating information

- Force heating ON:

- Normal operation:

- Heater temporarily OFF:

Button operations in the heater control menu

and

buttons

Change the digit (select the target of the operations)

and

buttons

Change the heater temperature or the heater operation.

button

Set the afterheater, printheater, or preheater on and off individually.

«
...
193
194
195
196
197
...
»

Содержание IP-5530










































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды