Oilon EasyAce страница 9 Скачать руководство пользователя

Страница: 9 / 54

2.2 Heating

Heating circuits and their temperature

To change the heating circuit displayed in the

Home

view, tap the circuit’s number.

The

Heating circuit

window appears. Select

another circuit, and tap

OK.

Circuit 1

is now displayed in the

Home

view.

If the heating circuit has no room temperature

measurement available, the display shows the icon

for increasing and decreasing heating (see sub-

section

Increase or decrease heating

If the heating circuit’s

flow temperature

measurement

is enabled, the flow water

temperature is displayed next to the circuit number.

If the heating circuit’s

room temperature

measurement

is enabled, the relevant room

temperature will be displayed instead.

Increase or decrease heating

The

Home

view includes an icon for increasing or decreasing heating in the selected

circuit. This icon will not be displayed, if the circuit has no room temperature

measurement available (or room temperature optimization has been disabled).

M8004 2308EN

7 (49)

Содержание EasyAce























































Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды

Oilon EasyAce, Руководство по эксплуатации

Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды