Oilon EasyAce Скачать руководство пользователя

Страница: 36 / 54

6.3 Setting up a heat pump connection

1. Enter the Unit ID.

Each heat pump has a unique

Unit ID

. Either type in the ID or

scan the heat pump’s QR code

with a camera. The ID is on the

heat pump’s front panel.

2. Read the

Terms of Service

Read the

Terms of Service

. Return

by tapping the top left or right

corner.

3. Accept the

Terms of Service

If you do not accept the

Terms of

Service

, you won’t be able to use

the heat pump with your device.

4. Connect EasyAce to the heat

pump’s Wi-Fi network.

● If you selected Cloud

connection as the connection

type, go directly to step 5.

Exit the app, and connect your

mobile device to the heat pump’s

Wi-Fi network.

● Connect your device exactly

as you would connect to any

other Wi-Fi network. See

section

Connecting a mobile

device to the data hub’s Wi-Fi

network

● The name and password for

the Wi-Fi network are on the

unit’s front panel.

5. Select the connection type.

If you select

Cloud connection

Local & Cloud

, the heat pump

needs to be connected to the

internet.

6. Give the password.

The password is on the unit’s front

panel.

7. Skip by tapping Continue.

This screen is not shown when

using a

Cloud

connection.

8. Enter the Connection ID.

The

Connection ID

is retrieved

automatically. Tap

Continue

● This screen is not shown

when using a

Local

connection

9. Name your heat pump.

Tap

Continue

. The connection

between your device and the heat

pump has now been established.

6.3.1 Local connection

The wireless touch screen delivered with the unit comes with the

connection already established. The wireless touch screen uses a local

connection.

34 (49)

M8004 2308EN

Содержание EasyAce























































Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды

Oilon EasyAce, Руководство по эксплуатации

Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды