manualshive.com logo in svg

OHAUS T72XW AM, Инструкция по эксплуатации

Поделиться
Скачать
OHAUS T72XW AM Скачать руководство пользователя страница 29

7000 SERIES INDICATORS 

EN 21 

 

 
 

Table 2-7: Information Recall Menu Items 

Item 

Value/Explanation 

Model 

The model number of the indicator is shown. 

Serial No. 

Serial number of the indicator as entered in the setup mode. 

Option 1 

Shows installed hardware options, if any. 

Option 2 

Firmware 

Shows the firmware revision number. 

Service 

A telephone number used to contact OHAUS CORPORATION 
authorized service. 

Approved 

Yes 

or

 No 

Indicates whether the indicator has been programmed as Approved 
for use in legal for trade applications. 

Certificate 

# 

Displays approval certificate number. 

Calibrated 

Shows date of most recent calibration. 

IP 

Address 

IP address assigned to the indicator. 

2.3.9 

Setup Access 

The last icon displayed in the 

OPERATOR

 menu accesses the 

SETUP

 menu, from which all the indicator

’s  

programming parameters can be viewed and modified. The settings and options available in setup are described in 
detail in Chapter 3, Configuration: Indicator. 
 
It is not intended that operators enter the setup mode. After a weighing system is installed and is operational, it 
should not be necessary for an operator to access setup. 
 
Note that a security password can be enabled in setup. When a password is set, it must be entered in order to 
access setup. This protects the setup parameters from inadvertent changes. 

2.4  Basic Functionality 

This section provides information about T72XW basic functionality. Functions addressed in this section include: 
 

 

Zero 

 

Clearing Tare 

 

Information Recall 

 

Tare 

 

Print 

 

Target 

 
Refer to Chapter 3, Configuration: Indicator, for further information about programming all the functionality 
described in this section. 

2.4.1 

Zero 

The Zero function is used to set or reset the initial zero reference point of the indicator. There are three types of 
zero setting modes: 

 

Automatic Zero Maintenance 

 

Power Up Zero 

 

Pushbutton Zero 

When the scale platform or weighbridge is empty, the indicator should indicate zero. The gross zero reference is 
recorded during calibration. If pushbutton zero is enabled in configuration and the weight is within the zero range 
pressing ZERO will capture a new gross zero reference point. 
 
 
 
 
 
 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание T72XW AM
















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды