manualshive.com logo in svg

OHAUS T72XW AM, Инструкция по эксплуатации

Поделиться
Скачать
OHAUS T72XW AM Скачать руководство пользователя страница 14

EN 6 

7000 SERIES INDICATORS 

 

 

1.11.4  SD Memory Option 

An optional SD Memory card provides a medium on which to store files such as Alibi Memory, IDs in the Counting 
application, target weights in the Checkweighing application and truck weights in the Vehicle application. 
 
Note: The SD card is required for Alibi Memory and Vehicle Weighing. 

The SD memory can also be used to extract and save the configuration and calibration settings of the indicator. 
These can then be restored to the indicator or loaded to a different indicator. This feature can be used to clone the 
setup of one indicator then transfer it to other units, which minimizes the chance of error in setting up a new 
configuration. 
 

1.12  Installation 

Opening the Enclosure 

The front panel of the harsh enclosure T72XW indicator is locked in place by six spring clips attached to the body of 
the enclosure. To access the indicator

’s PCB to install options, connect internal wiring and set switches, separate 

the front panel from the enclosure as follows: 
1.  Insert the tip of a flat-blade screwdriver into one of the two slots located on the bottom of the front panel 

assembly (see Figure 1-2). While squeezing the front panel and enclosure together, gently push the 
screwdriver in toward the enclosure. A “pop” sound is made when the cover clip is released. 

 

Figure 1-2: Opening the Harsh Enclosure 

2.  Repeat Step 1 for the other slot. 

3.  After releasing the two clips securing the bottom of the front panel, move the panel to each side to disengage 

the side clips, then lift the bottom of the front panel firmly up and out (Figure 1-3, 

1

) until it completely clears the 

top edge of the bottom enclosure. 

4.  Squeeze the top of the front panel to the enclosure along the top edge slightly and push upward (Figure 1-3, 

2

) 

to unsnap the top two clips, then lift the cover to clear the two top clips. The cover will swing down, hinged by 
two wire cables at the bottom.

 

 

Figure 1-3: Removing the Cover 

 

 

1 

2 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание T72XW AM
















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды