manualshive.com logo in svg

OHAUS T72XW AM, Инструкция по эксплуатации

Поделиться
Скачать
OHAUS T72XW AM Скачать руководство пользователя страница 115

7000 SERIES INDICATORS 

EN 107 

 

 

APPENDIX C    COMMUNICATIONS 

 

C.1 Serial Interface Parameters 
 

One standard serial port and one optional serial port are supported with the T72XW indicator. They are designated 
COM1 (standard port on the Main PCB) and COM2 (optional). 
 

COM1 

provides an RS-232 interface only. The RS-232 interface is a three-wire (TDX, RXD, and GND) with 

selectable XON-XOFF handshaking. 
 
Optional 

COM2

 provides RS-232 and RS-485 interfaces. The RS-232 interface is a three-wire (TDX, RXD, and 

GND) with selectable XON-XOFF handshaking. The RS-485 connection is a two-wire interface but does not 
support multi-drop communication with addressing. The port must be selected for use as either RS-232 or RS-485 
due to the different operating requirements of the interfaces. 
 
The baud rate can be configured from 300 to 115.2K baud and a checksum character can also be configured when 
using one of the continuous output strings. 
 
The T72XW indicator supports the following functions on the serial ports: 

 

SICS (level 0 and level 1) 

 

Reports  

 

Continuous 

 

The COM1 port is also used when flashing new firmware to the indicator. 

 

Demand Output Mode 
 

The demand output mode transmits data only when the indicator receives a print request. Print requests are sent to 
the T72XW indicator when: 

 

The operator presses PRINT 

 

A discrete input selected as print is triggered 

 

An ASCII “P” is sent through a demand or continuous port 

 

Auto print is enabled and all conditions for auto print are met 

 
When triggered, data is transmitted in a string programmed in the output template portion of setup. Demand mode 
is used typically when sending data to a printer or PC on a transactional basis. 
 
NOTE: When the demand output mode is assigned, the port is automatically set up to also receive certain ASCII 
characters to duplicate keypad functions.  
 
Output Templates 
 
The T72XW indicator provides three programmable output templates to define the string of data to be transmitted. 
Each of the templates is configured in setup and can contain up to 25 fields of data. The same template can be 
sent to both COM1 and COM2 if both ports are programmed for demand output. It is also possible to send a 
different data string from the two ports by assigning a different template to each one. 
 The default values for each of the templates follow: 
 
Template 1 
 

    29.94 kg 

 

    10.32 kg    T 
    19.62 kg    N 

 
 
 
 
 
 
 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание T72XW AM
















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды