OFF CARR IDRA 2.0 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 23

OFF CARR IDRA 2.0 Скачать руководство пользователя страница 11

11

4.4

Replacing the front castors

If necessary, the front castor can be replaced:

•

Completely unscrew one of the “D” screws and

remove the “E” pin being careful to where the “F”

spacers are;

•

If necessary, change the wheel;

•

Position the wheel hub align with the most suitable

fork hole;

•

Insert the “E” pin, being careful to keep the “F”

spacers in their original sequence;

•

Fix properly the “D” screw.

Be sure to choose the same position for both castors. Asymmetrical combinations

produce instability.

Be careful not to change the front seat height while changing the front castors

because this will modify the perpendicularity to the ground of the front fork roataing

axle.

4.5

Backrest tension adjustment

The backrest tension can be adjusted by acting on the

velstraps:

•

Fold up the “B” upholstery cover of the

backrest;

•

Adjust the upholstery tension by opening or

closing the disclosed velstraps;

•

Fold down the “B” upholstery cover back in

place;

4.6

Backrest height adjustment

The backrest height will be assembled according to the order form selection. It is however

possible to change it over time.

If the wheelchair is equipped with pushing handles it is possible to move them up or down of

a few centimetres as shown:

«
...
9
10
11
12
13
...
»

Содержание IDRA 2.0
























Отзывы:

Нет отзывов