background image

1. Description 

 

1.1 Validity 

 

1.1.1 Catalog 

Number 

 
This document is valid for the following products: 
 

Catalog Number 

Product 

Version 

Serial Number 

230001 

DISPLAY ONE with mains cord, EU version 5.ff  

10001 - 19999 

235001 

DISPLAY ONE with mains cord, US version 5.ff  

10001 - 19999 

 
Table 1 

– 

Catalog Numbers

 

 
 

1.1.2 Nameplate 

 
A nameplate is located on the bottom side of the instrument. When communicating with 
Oerlikon Leybold Vacuum GmbH, the information on the nameplate will be needed. For 
this reason enter the information here: 
 

 

 

Figure 1 

– 

Nameplate (example) 

 
 

1.2 Conforming 

Utilisation 

 
The DISPLAY ONE serves as a simple power supply and display unit for the transmitters 
from the series THERMOVAC and PENNINGVAC. 

 
 
1.3 

Responsibility and Warrenty 

 

Oerlikon Leybold Vacuum GmbH will assume no responsibility and warranty when the 
operator or third parties 
 

  do not observe the information provided in this document. 

  do not use this product in line with the conforming utilisation 

  modify the product in any way (modifications, repair work etc.) 

  operate the product with accessories which is not listed in the corresponding 

product documentation 

 

The right of changes without prior announcement is reserved. The illustrations are not 
binding. 
 
 

 

GA 09.034/2.02 – 07/10

 

Содержание 230001

























Отзывы: