background image

 

 

 
 
 
 

 

 

20 

 

6. ADVANCED FUNCTIONS 

 
 

6.3. Protection  
 

The V 110 SE features a comprehensive electronic monitoring and protection system. This system 
will automatically switch off the V 110 SE if case of a fault occurring in the power section.  
The  protection  system  has  been  designed  to  keep  the  unit  safe  from  the  consequences  of 
overloads of any kind and to protect the output tubes from current surges. 
 
The red “Protection” LED lights up in [No. 6, chapter 4] to indicate that the protection system has 
tripped. 

 
The amplifier will not play music once the protection system has tripped and you will 
not be able to check or adjust the BIAS setting. 

 
The BIAS LEDs will show "yellow" for each of the four output tubes. 
If a Black Box or a Super Black Box is connected to the V 110 SE, the front panel (operate) LED of 
the  Black  Box  /  Super  Black  Box  will  go  out.  If  the  Super  Black  Box  is  connected,  tripping  the 
protection  system  will  automatically  activate  the  discharge  circuit  of  the  (Super)  Black  Box  (see 
chapter 10). 
  
The following conditions can cause the protection system to trip: 

Overdriving the V 110 SE to excessive levels or with excessive levels of low frequency.  

A speaker cable short circuit while the speakers are being driven at high listening levels. 

A fault in one or more of the output tubes. 

A fault in one of the preamp tubes which overloads the affected channel. 

 
Once the protection system has cut in, the only way you can turn the V 110 SE back on is to turn 
the on/off switch off and then on again. Allow the unit two minutes to cool down before switching it 
back  on.  If  possible,  identify  and  eliminate  the  cause  of  the  problem  (see  chapter  11 
"Troubleshooting"). 
 
If it is not clear what has caused the protection system to trip, we recommend that you check the 
BIAS  before  attempting  to  use  the  amplifier  again.  Tube  faults  can  often  result  in  widely  varying 
BIAS settings. When these settings exceed a particular value they can cause the protection system 
to trip. 

 
 

6.4. Soft-Start 

  
The V 110 SE input and output tube heaters as well as its high-voltage rails are logic controlled to 
ensure  that  the  conduction  of  the  output  tubes  as  well  as  input  stage  voltages  are  constantly 
monitored  and  controlled  by  the 

Power  Management  system

  to  protect  the  vital  internal  parts 

(tubes, rectifier, electrolytic caps, switches, etc.) against excessive turn-on current. This increases 
the  lifetime  not  only  of  the  tubes,  but  also  the  caps,  while  all  power  related  components  derive 
benefit through this system. 
  
The Soft-Start is always activated within the first 60 seconds after the unit is switched on. During 
this time you cannot listen. The Soft-Start delay is indicated with the Soft-Start-LED.  

 
During the Soft-Start-phase, adjusting the BIAS is not possible. 
  

Содержание V 110 SE







































Отзывы: