Box Contents
Remove Top Shroud &
Attach Pedals
A
Hardware Pack
110507-001 REV D Page 1/2
USA & Canada
888-OCTANE4
Latin America/Asian Pacific
001-763-757-2662
Europe/Middle East/Africa
31-10-2662412
Questions?
octanefitness.com
©2015 Octane Fitness. All rights reserved.
C
Base
109100-001
Tools Required:
#2 Phillips Screwdriver
13 mm wrench (2)
Frame End Covers
(Left and Right)
110379-001
110380-001
Mast Boot
109528-001
Console Mast
110037-001
Moving Handlebars
(Left and Right)
109261-001
109258-001
Handlebar Covers
(Left and Right)
110047-001
110046-001
Information Packet
110507-001 Assembly
107786-001 Safety Instructions
Assembly Instructions
Hardware Pack
110525-001
B-1 (1)
107005-001
13mm
B-2 (1)
103393-001
13mm
#2 Phillips
B-3 (6)
102135-001
B-4 (2)
101720-001
17mm
B-5 (2)
106618-001
17 mm wrench
B-6 (2)
103395-001
17mm
B-7 (2)
100429-001
#2 Phillips
Complete steps 1 - 3 before removing unit from base box tray .
With Phillips #2 screwdriver, remove 4 screws and top shroud; set aside for
re-installation in Step E-4.
Right pedal is not attached.
Break away all 4 corners of base tray, then carefully
remove packaging from rear of pedals while supporting the pedals.
Bring pedals carefully to stable resting position (not shown).
Align top bracket of right pedal lever with top of 3-pivot link. Insert bolt B-1 from
outside of unit through both parts and secure with nut B-2. Tighten to 17 ft-lbs
using two 13mm wrenches.
With help, lift unit and roll off front of box tray (not shown).
(Unit weighs approximately 400 lbs. (181 kg).)
With Phillips #2 screwdriver, remove 4 screws from access tray; set screws aside
for re-installation in Step 3.
Slide access tray back toward rear of machine. Slide mast over 4 screws on base;
tighten with 6mm hex wrench.
Slide access tray forward; secure with 4 screws retained in Step 1.
Remove wire twist ties securing cable bundle under mast plate; route cables up and
out the top of the mast (not shown).
For each moving handlebar:
Slide moving handlbar onto pivot shaft.
Slide end link over small crank arm.
Slide washer B-4 onto bolt B-5, then insert bolt into moving handlebar pivot shaft.
Tighten with 17mm wrench to 33 ft-lb.
Secure end link to small crank arm with nut B-6; tighten with 17mm wrench
to 33 ft-lb.
Hook plastic clip on moving arm cable over hole in frame; secure with screw B-7
using Phillips #2 screwdriver. Connect moving arm cables (2) to cables in base.
Select the correct handlebar cover, labeled “R” (right) or“L” (left). Position small
slot in handlebar cover around moving handlebar and press into place, covering
the moving handlebar pivot shaft.
B
Install Mast
Install Moving
Handlebars & Covers
Console Box Contents
100924-001
6mm Hex (1)
6 mm hex wrench (provided)
Tools Required:
#2 Phillips Screwdriver
Information Packet (attached to console)
110601-001 Notice to Installers
110506-001 Console Guide & Set-up Instructions–
Standard Console
104198-001 Warranty
101315-001 Registration Card
Standard Console
(Front and Back)
110460-001
Tools Required:
#2 Phillips Screwdriver
110601-001 Notice to Installers
110600-001 Console Guide & Set-up Instructions–
Smart Console
104198-001 Warranty
101315-001 Registration Card
Information Packet (attached to console)
Smart Console
(Front and Back)
110865-001
Power Switch
111032-001
Switch Cable
111033-001
Power Supply
107057-001
Power Cord
107658-001
#2 Phillips
C-1 (10)
100780-001
Hardware Pack
110622-001
#2 Phillips
C-1 (10)
100780-001
Hardware Pack
110622-001
(may be boxed separately)
(may be boxed separately)