Ochsner AIR FALCON 212 Скачать руководство пользователя страница 10

Страница: 10 / 88

www.ochsner.com | 00_200_202_08_02_001-EN

Appliance description

4. Appliance description

4.1 Scope of delivery

The scope of delivery of your appliance includes the fol-

lowing components.

►

1 indoor unit

The following components are installed in the in-

door unit:

- Flow meter (heat sink side)

- Heat generator pump

(circulation pump)

- Safety valve

- User interface

- OTS heat pump controller

- Diaphragm expansion vessel 24 l

- 3-way switching module (DHW)

- Electric auxiliary heater

- Bypass pipe

►

1x outdoor unit:

The following components are installed in the

outdoor unit:

- Evaporator

- Expansion valve

- Fan

- Compressor

►

1 outdoor temperature sensor

►

1 contact sensor:

For a mixed circuit

►

2 cable temperature sensors

►

2 solder adaptors

►

1 Ochsner service book

4.2 Indoor unit hydraulics

The system must be engineered using an OCHSNER

standard hydraulic schematic or an OCHSNER special

hydraulic system.

1 Liquid line

2 Hot gas line

3 DHW return

4 Heating water return

DHW flow

Heating water flow

7 Safety valve

8 3-way switching module

9 Flow meter

10 Heat generator pump (circulation pump)

11 Electric auxiliary heater

12 Heat exchanger (heat sink side)

13 Diaphragm expansion vessel

14 System pressure sensor

15 Bypass pipe

16 Temperature sensor

Shut-off valve

18 Fill and drain stopcock

4.3 Appliance components

4.3.1 Indoor unit

The indoor unit is intended to be installed inside the build-

ing only. The casing is acoustically optimised and allows

particularly quiet operation.

Electric auxiliary heater:

The appliance is fitted with an electric auxiliary heater

(immersion heater). At low outdoor temperatures, the ap-

pliance operates in bivalent-parallel mode.

Содержание AIR FALCON 212

























































































Результаты поиска

Содержание AIR FALCON 212

Отзывы:

Бренды по названию

Популярные бренды

Ochsner AIR FALCON 212, Руководство по эксплуатации

Результаты поиска

Содержание AIR FALCON 212

Отзывы:

Бренды по названию

Популярные бренды