Ocean Signal rescureME MOB1, Быстрый старт

Страница: 3 / 4

2017­5­17 MOB1 ­ Ocean Signal
http://oceansignal.com/products/mob1/ 3/4
FREQUENTLY ASKED QUESTIONS
What test modes does the MOB1 have?
There are three test modes on the MOB1; Functional, DSC and
AIS/GPS.
The Functional test should be carried out once a month and will
display the length of time the battery has been used for. It will also
apply a load to the battery to test that the battery is not faulty or has
been discharged. It carries out other functional tests on the electronic
circuitry. It does not test the GPS or make test transmissions.
The DSC test should be carried out no more than two times a year.
This test sends a single DSC transmission to the MMSI programmed
into the MOB1, which will be displayed on the vessels DSC radio. It
does not send a Distress or Distres Relay call and the call does not
contain the position.
The AIS test should be carried out no more than three times a year.
This test activates the GPS receiver and after the position is
determined it makes an AIS transmission, which will display on a
suitable AIS receiver or chartplotter. The received AIS message will
show the position determined by the MOB1 GPS receiver. There is
also a transmission of the AIS text message containing the words
“MOB TEST”. Note that this test must be done with the MOB1 in full
view of the sky. Without a valid position, the MOB1 will not transmit
any AIS messages.
The limitation on the number of tests a year is to ensure that the
battery will still have its full operational life at the expiry date of the
battery.
Why does my MOB1 show red flashes if I try to programme the
MMSI number?
If the unit fails to programme, showing the flashing red LED on
completion, please try again. Turn the MOB1 on in programming
mode again and retry. There is no need to exit the programming
screen on the programme. If the programming page is showing,
simply press F10 again to commence the programming sequence
again. Note that the red flashing may tecke several seconds to start
after the on screen sequence has finished.
If you are having problems programming your MOB1, please check the
following guidance.
1) Make sure that your screen brightness is set to maximum, using the
controls on the monitor or device.
2) Ensure that you have commenced programming within 50 seconds
of putting the MOB1 into programming mode. Failure to do this will
cause the MOB1 to have turned off before communication starts. Note
that once programming has commenced (The white box is flashing) the
MOB1 should stay on until the programming sequence is completed.
Ideally the MOB1 should be put into programming mode just before
placing the MOB1 in front of the white square.
3) Ensure that the MOB1 is placed over the white square with the
rubber programming adaptor firmly touching the screen and with the
aperture in the rubber close to the centre of the white box.
4) Avoid programming the MOB1 in bright ambient light conditions. If
necessary point the screen away from direct or bright sources of light
such as sun through a window. (In extreme circumstances, especially
with older screens that have lost their brightness, place a thick cloth
over the screen and MOB1 to block out the ambient light.)
5) The MOB1 configuration software requires precise timing, which
may be disrupted by other applications running at the same time,
especially on slower computers. If you still encounter problems, try
shutting down all un­necessary applications, including anti­virus
software.
6) On laptops, the F10 key will require using in conjunction with the
Function (labelled Func or Fn) to start the white box flashing black and
white to send the data to the MOB1. Most keyboards will colour the F
keys in the same colour as the Function key to identify this.
7) The MOB1 MMSI programming software is only available for
Windows PCs. For users of other operating systems and smart
phones and tablets there is an online application available. This can
be accessed using the
button on the installers
(http://oceansignal.com/installers/) web page. Note that it can only be
used online.
Which DSC radios are compatible with the MOB1?
Ocean Signal recommends using one of the radios from the list below
with the rescueME MOB1. The following class D DSC radios have
been tested in cooperation with the manufacturer and confirmed to
receive the Individual Distress Relay call.
ICOM:
Current models; M91, M323, M423, M506
Older models; M411, M421, M505, M603
Simrad: RS90
Standard Horizon: GX1600E (Explorer); Newer models are also likely
to work but have not been tested.
Class A DSC radios have always been able to receive this call and all
models are believed to be compatible.
This list is not exhaustive and will be added to as more compatible
models are confirmed.
Ocean Signal welcomes enquiries from other manufacturers wishing to
have their radios listed here.
What DSC functions are allowed in my country?
The DSC functionality of the MOB1 is limited by regulations in each
country. The list below indicates which functions you may expect.
AIS only: Canada, France, Denmark, Latvia
AIS + DSC Individual Distress Relay call plus group call sent after
30minutes: USA
AIS + DSC Individual Distress Relay call only: Germany, Netherlands,
Spain, United Kingdom
AIS + DSC Individual Distress Relay, All Ships Distress Alert (manual
initiation only): All other European countries
AIS + DSC Individual Distress Relay, All Ships Distress Alert, sent
once on MOB1 activation and on manual initiation: Rest of the World.