Oce VarioPrint 6000 Plus Line Скачать руководство пользователя страница 63

Страница: 63 / 102

Clean the OPC belt (left)

Procedure

IMPORTANT

Do not touch the OPC belt with your fingers. Wear cleaning gloves.

Rotate the metal OPC pulley to locate the spot(s) on the OPC.

[74] Rotate the OPC pulley to locate the spots

Rotate the OPC pulley until the spot(s) are in the indicated area

NOTE

In this area, the OPC has a hard bottom surface which is required to enable proper
cleaning without damaging the OPC belt.

[75] Position the spot(s) in the indicated area

Apply a small amount of Cleaner J on an offset pad.

Clean the spot(s) with this offset pad.
When you cannot clean the spots with Cleaner J, use Cleaner P.

Clean the OPC belt (left)

Chapter 3 - Maintenance tasks - Level 2

Océ VarioPrint 6000 line

Содержание VarioPrint 6000 Plus Line







































































































Результаты поиска

Содержание VarioPrint 6000 Plus Line

Отзывы:

Похожие инструкции для VarioPrint 6000 Plus Line

Бренды по названию

Популярные бренды

Oce VarioPrint 6000 Plus Line, Руководство по обслуживанию

Результаты поиска

Содержание VarioPrint 6000 Plus Line

Отзывы:

Похожие инструкции для VarioPrint 6000 Plus Line

Бренды по названию

Популярные бренды