Oce Arizona 318 GL Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 224

background image

Safety Labels

Introduction

The safety labels are placed at strategic locations on the printer to warn the operator of possible
dangers and hazards. It is important to be aware of the meaning of these labels to ensure safe
operation of the printer.

Do not remove caution labels. If a label is soiled, please clean the label. If you cannot make labels
legible, or if the label is damaged, please contact your service representative.

Safety Labels

Description

Label

Warning: UV Light Hazard.

Avoid looking directly at UV lamps.
Located on carriage cover to remind the operator that
looking at the UV light source is dangerous.
Wear protective eye-wear with side shields, gloves and
long sleeves when using this printer.
Ultraviolet Light Radiation Hazards Emission: Effective UV-
irradiance Emission Category according to 7.1 of
EN12198-1:2000 - - Special restrictions and protective
measures are essential when the machine is used in the
workplace.

Wear Safety Gloves

Located on the maintenance station as a reminder to al-
ways wear gloves when handling ink.

Risk of Eye Injury. Wear Eye Protection -

Located on the

maintenance station as a reminder that the UV-curable ink
is harmful to the eyes and skin. Always wear glasses and
gloves when handling ink.

Machine lockout:

a reminder to turn off and lock out the

AC power switch before servicing any electrical compo-
nents.
Located on the mains power switch.

Warning: Electric Shock Hazard

Located on the door to the electronics enclosure, the UV
lamp power supply cover, the carriage cover, and the vac-
uum pump enclosure. This area can only be accessed by a
trained service technician.

General Warning

Located on the AC enclosure cover. This area can only be
accessed by a trained service technician.

4

Safety Labels

Chapter 3 - Safety Information

23

«
...
21
22
23
24
25
...
»

Содержание Arizona 318 GL

































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 318 GL

VersaLink C400V

Бренд: Xerox Страницы: 196

Бренд: Oki Страницы: 72

Бренд: MUTOH Страницы: 148

Бренд: Ultimaker Страницы: 4

Бренд: Dascom Страницы: 2

Бренд: Code Soft Страницы: 101

Бренд: TRENDnet Страницы: 135

Бренд: Ricoh Страницы: 177

Бренд: Canon Страницы: 1384

Бренд: Canon Страницы: 642

Бренд: Xerox Страницы: 34

Бренд: Plockmatic Страницы: 76

Бренд: Epson Страницы: 10

IMAGERUNNER 7086

Бренд: Canon Страницы: 14

imageRUNNER 5055

Бренд: Canon Страницы: 4

imageRUNNER ADVANCE C2225

Бренд: Canon Страницы: 109

imageRUNNER ADVANCE 525 I

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды