background image

 

 

Copyright 2010-2012 Obihai Technology, Inc. 

136 

LINE Port Parameter Guide: 

Parameter 

Description 

Default Setting 

LINE Port 

 

 

Enable 

Enable the LINE port 

Yes 

DigitMap 

Digit map to restrict numbers that can be dialed or 
called on the PSTN line.  
 
See 

OBi Call Routing and Digit Map Section

 for a 

description of the syntaxes for specifying a Digit 
Map. 

(xxxxxxxS4|1xxxxxxxxxx|xx.) 

InboundCallRoute 

Routing rule for directing incoming calls on PSTN 
line. The default rule is to send all incoming calls to 
the PHONE port (ph).  
 
See 

OBi Call Routing and Digit Map Section

 for a 

description of the syntaxes for specifying this 
parameter 

ph 

RingDelay 

Delay in milliseconds after initial ring detected on 
the LINE port before the device acts on the call (to 
route it according to InboundCallRoute). This value 
could be 0 so that the call is handled immediately. 
However, you should consider setting it to a large 
enough value to allow OBi to completely decode 
the PSTN Caller-ID signal if the service is available 
on the PSTN line. This is required if the 
InboundCallRoute relies on Caller-ID information 
to route the incoming call. 

5500 

RingProfile 

Select a Ring Profile to ring the PHONE port with 
when an incoming call is routed to the PHONE 
port. Choices are A, or B 

DefaultRing 

Default ring pattern number to ring the PHONE 
port for incoming calls on this trunk that are 
routed to the PHONE port according to the 
InboundCallRoute of this service. The ring pattern 
is taken from the selected Ring Profile. Valid 
choices are 1-10 

CallOnHoldRing 

Pattern to ring PHONE port when holding a call on 
this trunk that has been connected to the PHONE 
port. Typically this is a very short distinctive ring 
pattern that serves as a reminder to the user that a 
call is being on hold. The ring pattern is taken from 
the selected Ring Profile. Valid choices are: NO 
Ring, or 1-10 

Tone Profile 

Select a tone profile for tone detection to support 
the detection of outbound call connected state 

DetectOutboundConnectMethod 

Select a method to detect if an outbound call on 
the PSTN line has been answered. It can be one of 
the following values: 

-

 

None: Do not detect call connected state. 
Device will simply assume the call is 
connected once it finishes dialing 

-

 

Detect speech: Device will detect speech 
signal on the line as a positive indication 
of call connected state. 

None 

Содержание OBi110











































































































































































































Отзывы: