Obihai OBi100 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 220

background image

Copyright 2010-2013 Obihai Technology, Inc.

56

WAN Status

The status of the WAN (Ethernet) interface: includes such information as the assigned IP address, default gateway and
subnet mask.

WiFi Status

This status is only available on the OBi202 and OBi302. This shows the status of OBiWiFi and includes such information as
the assigned IP address, default gateway and subnet mask.

Product Information

This status shows some basic product information, as well as the system up-time with the last reboot reason code in
parenthesis. The reboot reason codes are defined below.

Reboot Reason Codes

0:       Reboot on Power Cycle
1:       Operating System Reboot
2:       Reboot after Firmware Update via provisioning or phone (***6)
3:       Reboot after New Profile Invoked
4:       Reboot after Parameter Value Change or Firmware has changed and invoked via device web page
5:       Reboot after Factory Reset using the OBi device hardware pin
6:       New Profile Invoked AND Profile URL Changed
7:       Reboot from SIP Notify (Reserved)
8:       Reboot from Telephone Port (IVR)
9:       Reboot from Webpage - No change in parameter value(s) or firmware
10:     Reboot During OBiTALK Signup
11:     Reboot During OBiTALK Signup
12:     Reboot after DHCP server offers IP, GW-IP and/or Netmask different from what the OBi device is currently using
13:     Reboot on Data Networking Link Re-establishment
18:     Reboot on WAN IP address change (OBi202/OBi302 only)
19:     Reboot on LAN IP address change (OBi202/OBi302only)

OBiBT Bluetooth USB Adapter 1/2 Status

This status is available on OBi202 and OBi302 only. It shows the status regarding the OBiBT USB adapter attached to the
unit and the corresponding OBiBlueTooth Services. The following status values are available:



State – It can be one of the following values:

-

No Dongle: No authentic OBiBT dongle detected

-

Connecting <device-name>: Connecting to the named device

-

Disconnected: Not connected with any paired device

-

No Device To Connect: No device paired

-

Service Down: Connected to a mobile phone which does not have an active service (e.g., no SIM card or
no signal)

-

Service Disabled: OBiBlueTooth service has been disabled in the OBi configuration

-

Connected to <device-name>: Connected to the named device; OBiBlueTooth service is available only in
this state



Discoverable – It either shows “Not Discoverable” or the number of seconds for which OBiBT will remain
discoverable



CallState – It can be one of the following values:

-

Incoming Call: BT detected an incoming call, but ringing has not started yet

-

Ring <Caller-ID>: Mobile phone is ringing. <Caller-ID> is the caller’s number

-

Outgoing Call: Mobile phone is making a call that is not answered yet

«
...
54
55
56
57
58
...
»

Содержание OBi100





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OBi100

Power System 8247-21L

Бренд: IBM Страницы: 60

Бренд: Icom Страницы: 2

Бренд: Rotel Страницы: 8

Бренд: Aiphone Страницы: 8

Бренд: HQ Страницы: 37

Magic I/O EV-170

Бренд: Everex Страницы: 40

USB202 VIDEO/AUDIO TO USB 2.0 ADAPTOR

Бренд: Atlona Страницы: 26

Бренд: Proyecson Страницы: 148

Бренд: Linksys Страницы: 87

ThinkPad Enhanced Drive Adapter

Бренд: IBM Страницы: 82

Бренд: Amped Wireless Страницы: 2

Бренд: StarTech.com Страницы: 2

1520A - AHA Storage Controller Fast SCSI 10 MBps

Бренд: Adaptec Страницы: 62

Бренд: Planet Страницы: 2

Бренд: ETAS Страницы: 57

Бренд: OTC Wireless Страницы: 29

Бренд: Rocstor Страницы: 2

Бренд: Rocstor Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды