Obihai OBi100 Скачать руководство пользователя страница 162

Страница: 162 / 220

162

PayloadType

Dynamic Payload type for this codec. Valid range is 96-127

105

iLBC Codec

Codec

Codec Name

iLBC

BitRate

Bit rate in bits/sec
Two values to choose from: 13333 bps or 15200 bps

13333

Enable

Enable this codec

SilenceSuppression

Enable silence suppression for this codec

PacketizationPeriod

Packet size in ms. Must be multiples of 30 for 13333 bps or multiples of 20 for
15200 bps

Priority

Priority assigned to this codec (1 is the highest)

PayloadType

Dynamic Payload type for this codec. Valid range is 96-127

FAX Event

Codec

Codec Name. This codec can be used for relaying FAX tone event using RTP

fax-event

Enable

Enable this codec

PayloadType

Dynamic Payload type to be used to indicate this event

100

FaxEvents

Comma separated list of event IDs to indicate (such as CED, CNG)

Telephone Event

Codec

Codec Name. This codec is for relaying DTMF events using RTP

telephone-event

Enable

Enable this codec

Yes

PayloadType

Dynamic Payload type to be used for RFC2833 telephone (DTMF) events. Valid
range is 96-127

101

Encap RTP

Codec

Codec Name. This codec is used to encapsulate RTP packets during a packet
loopback call

encaprtp

PayloadType

Dynamic Payload type for this codec. Valid range is 96-127

107

Loopback Primer

Codec

Codec Name. The codec is used by the OBi when acts as a media loopback
mirror and before receiving any packets from the loopback source during a
media loopback call

loopbkprimer

PayloadType

Dynamic Payload type for this codec. Valid range is 96-127

108

Codec Settings

G726BitPacking

Two values to choose from: big-endian or little-endian

big-endian

T38Enable

Enable the use of T38 (FAX Relay).

Note: Option not available on the OBi100 and OBi110

Yes

T38Redundancy

The packet redundancy factor to use when operating T38 relay. Available
choices are:

0 (no redundancy)

2 (higher redundancy; consumes more network bandwidth)

Note: Option not available on OBi100 and OBi110

FaxPassThroughCodec

The codec to use when operating in the FAX pass-through mode. Available
choices are:

G711U

G711A

G711U

Содержание OBi100









































































































































































































Результаты поиска

Содержание OBi100

Отзывы:

Похожие инструкции для OBi100

Бренды по названию

Популярные бренды

Obihai OBi100, Руководство администратора

Результаты поиска

Содержание OBi100

Отзывы:

Похожие инструкции для OBi100

Бренды по названию

Популярные бренды