O.S. engine MAX-12TR Series страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 30

background image

INSTALLING THE GLOWPLUG

Carburettor

Install washer on glowplug
and insert carefully into
cylinder-head, making sure
that it is not cross-threaded
before tightening firmly.

BASIC ENGINE PARTS

The MAX-12TR is high-perfomance
engines for 1/10 class R/C racing cars.
There are two verions, the one with 10M
carburettor and the other with 10J
carburettor. The MAX-12TR has a
conventional crankshaft, while the MAX-
12TR(P) employs a special crankshaft
with integral pilot shaft.

Crankshaft

Glow plug

Washer

Drive Hub

Crankcase

Beam Mount

Heatsink Head

Cover Plate

As delivered, the engine has its carburetor
lightly fit into its intake. Secure it changing
its angle according to the car chassis.

NOTE

NOTE: With this engine, the piston will feel
tight at the top of its stroke when the engine
is cold. This is normal. The piston and
cylinder are designed to achieve a perfect
running clearance when they reach their
normal running temperatures.

Standard accessories

Glow Plug A5

Super Air Cleaner 103 Assembly

103 Cleaner Body
103 Filter Elements (2pcs.)

Exhaust seal ring

Instruction manual

MAX-12TR

Exhaust

6

«
...
5
6
7
8
9
...
»

Содержание MAX-12TR Series































Отзывы:

Нет отзывов

Похожие инструкции для MAX-12TR Series

Бренд: JetCat Страницы: 54

Бренд: ebm-papst Страницы: 9

Бренд: Briggs & Stratton Страницы: 26

403F-E17T 404F-E22T

Бренд: Perkins Страницы: 108

Бренд: R.A. Lister Страницы: 84

Бренд: Hatz Страницы: 112

Бренд: Lombardini Страницы: 64

11LD522-3 Series

Бренд: Lombardini Страницы: 44

Бренд: Lombardini Страницы: 58

Бренд: Lombardini Страницы: 68

Бренд: Lombardini Страницы: 109

Бренд: YS Страницы: 2

Featherweight 45

Бренд: Seagull Страницы: 25

Бренд: Honda Страницы: 21

Бренд: Honda Страницы: 56

Бренд: DLE Страницы: 4

Бренд: DLE Страницы: 24

Бренд: O'Donnell Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды