O.S. engine GF40U-FI Скачать руководство пользователя страница 12

Страница: 12 / 36

①

Between the Fuel pump unit and Fuel pressure sensor unit

②

Between the Fuel pressure sensor unit and Injector coupler

Fuel tank

Fuel pump

・

The arrow mark shows the direction of fuel flow.

・

Apply a hose clamp to the pressurized side of the hose.

・

A one-way valve is built in the fuel pump so pressure remains in the fuel supply line even after stopping

the pump. Open the Pressure release valve to remove residual pressure.

・

Use a Non-bubbleweight in the tank to avoid creating air bubbles in the fuel supply tube. Air bubbles

may cause engine misfire and stalling.

・

Connect the tubes in the fuel tank firmly to the pipes in a fashion in which they will not easily come off.

Use clamps or wire ties if necessary.

・

Be sure to use [Code No. 28382303 FLUORINE (ETFE) RESIN TUBING (2m)] for piping between the fuel

pump unit and engine(

①

②

), through which pressurized fuel passes.

・

Fuel pump unit creates 300kPa pressure. Apply a hose clamp to each hose joint.

・

Connect the Pressure release valve nipple to the Fuel tank with a Return hose.

Installation

・

Connect the Fuel pump unit and the Fuel pressure sensor unit close to the Fuel tank.

・

Use a Fuel filter between Fuel tank and Fuel pump unit

Fuel tank

(not included in this set)

Fuel pump unit

Fuel pressure

sensor unit

pressure sensor

Pressure

release valve

Return hose

Connect to engine

Hose clamp

Fuel filter

Fuel delivery

Connect return hose

Connect fuel pump

Air vent

【

Example piping

】

Teflon rubber tube

Non-bubble weight

Connect fuel tank

Connect

Fuel pressure

sensor unit

Hose clamp

Содержание GF40U-FI





































Результаты поиска

Содержание GF40U-FI

Отзывы:

Похожие инструкции для GF40U-FI

Бренды по названию

Популярные бренды

O.S. engine GF40U-FI, Инструкция по эксплуатации

Результаты поиска

Содержание GF40U-FI

Отзывы:

Похожие инструкции для GF40U-FI

Бренды по названию

Популярные бренды