NXP Semiconductors UM10301 PCA8565 страница 34 Скачать руководство пользователя

Страница: 34 / 54

NXP Semiconductors

UM10301

User Manual for PCF85x3, PCF85x63, PCA8565, PCF2123, and

PCA21125

UM10301

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 2.1 — 23 July 2015

34 of 54

of the battery. Connecting the supercap directly in parallel with the normal decoupling

capacitor between V

and V

is possible, but it is recommended to use a series resistor

. The capacitance of the capacitor will change over its lifetime, especially at higher

temperatures. An increase of temperature by ten degrees results in a 50% decrease of

lifetime. Therefore be sure to specify extra backup time initially to allow for this decrease.
If backup is only needed for a few minutes to deal with short interruptions in power, it is

possible to use a small inexpensive electrolytic capacitor.
Supercaps cannot be bought from as many vendors as ordinary electrolytic capacitors.

They are available from such vendors as Panasonic, AVX and Cornell Dubilier. Important

specifications are working voltage and leakage current. If the rated working voltage is

only slightly exceeded, lifetime may be reduced. The leakage current should be as small

as possible. A standard electrolytic capacitor has a leakage current several times larger

than the timekeeping current consumption of the RTC and will limit the backup time

severely. Also leakage current of super capacitors can easily exceed the timekeeping

current consumption of an RTC and careful selection will result in longer backup time.
In most applications the lifetime of a supercap will exceed the lifetime of a NiCd or NiMH

battery. It decreases however with increasing temperature, humidity, applied voltage and

current. Although a supercap will often be the better choice as backup source compared

to rechargeable batteries in terms of available backup time, life time and cost (both for

relatively short backup times), for every specific application pros and cons of both must

be evaluated.

13.3.1 Charging the backup capacitor

Although not strictly necessary it is advised to charge the capacitor via a resistor in order

to limit the charge current. A resistor in series with a capacitor creates an RC-time

constant Τ. In order to calculate the charging time of the capacitor the following

parameters are important:

•

Capacitor value (i.e. 1 F)

•

Capacitor starting voltage (i.e. 0 V)

•

Series resistor (i.e. 4.7 kΩ)

The time constant T of the circuit equals R·C. The capacitor can be considered charged

after a time t = 5T. For this example t = 5 x 1 x 4700 = 23500 seconds. This is about 6.5

hours. This is the theoretical charging time of a capacitor with series resistance, but for a

supercap it may take even longer to become fully charged due to the many internal

series resistances with various values.
In this example the capacitor is charged to the supply voltage. Since the time keeping

voltage is lower than the supply voltage that is used in a typical application, it does not

take a time t = 5T for the capacitor to reach a voltage where it can start backing up the

RTC if main power would be interrupted.

13.3.2 Estimation of backup time with capacitor

In order to keep the calculations simple a constant current draw of the RTC is estimated

also when the supply voltage drops as the capacitor gets discharged. It is assumed that

the capacitor is fully charged. The following data is necessary for the calculations:

•

Cbackupstart

: The backup capacitor voltage when backup starts.

Содержание UM10301 PCA8565























































Результаты поиска

Содержание UM10301 PCA8565

Отзывы:

Похожие инструкции для UM10301 PCA8565

Бренды по названию

Популярные бренды

NXP Semiconductors UM10301 PCA8565, Руководство пользователя

Результаты поиска

Содержание UM10301 PCA8565

Отзывы:

Похожие инструкции для UM10301 PCA8565

Бренды по названию

Популярные бренды