manualshive.com logo in svg

NXP Semiconductors SJA1105SMBEVM, Руководство пользователя, Страница: 12 / 35

Поделиться
Скачать
NXP Semiconductors SJA1105SMBEVM Скачать руководство пользователя страница 12

 

 

NXP Semiconductors 

AH1721 

 

SJA1105SMBEVM UM 

AH1721 

All information provided in this document is subject to legal disclaimers. 

© NXP Semiconductors N.V. 2018. All rights reserved. 

User Manual 

Rev. 1.00 

— 16 July 2018 

12 of 35 

Table 5. 

Pinning of the debug connector J10 

Meaning/Name 

Pin 

Pin 

Meaning/Name 

JTAG_TDI 

1 

2 

GND 

JTAG_TDO 

3 

4 

GND 

JTAG_TCK 

5 

6 

GND 

n.c. 

7 

8 

n.c. 

JTAG_RESET (PowerPC Reset) 

9 

10 

JTAG_TMS 

VREF (3V3) 

11 

12 

GND 

n.c. 

13 

14 

JCOMP (10k pulldown) 

 

4.9  Buttons and switches 

Table 6. 

Buttons and switches  

Name 

Meaning/Usage 

SW1 

Wakeup 

– connects the PHYs’ wakeup line with VCC – this is for wakeup/sleep  

SW2 

Reset button 

– controls the uC’s reset input. 

SW3, 
SW4 

General purpose buttons connected to interrupt capable GPIOs 

SW3: Button0 

SW4: Button1 

SW5 

Rotary switch with 16 positions 

The software can make use of the rotary switch to select a specific board configuration.  

The example software project uses the rotary settings in the following way to 
enable/disable ethernet and/or CAN operation:  

Table 7. 

Rotary switch configuration in the example project 

Configuration: 

Ethernet operation 

CAN operation 

0 

no 

no 

1 

yes 

yes 

2 

yes 

no 

3 

no 

yes 

4-F 

Not used 

– see configuration #0 

For ethernet operation, the switches and PHYs are initialized and configured with a 
simple setup, and the µC periodically sends out a packet on its both ethernet ports 

– one 

port connected to the switches and another one to the FE port. 

For CAN operation the µC periodically tries to send out a CAN telegram, and reports 
received telegrams on the serial console. 

5.  Getting started 

The following steps are required to bring the SJA1105SMBEVM into operation: 

1.  Installation of the software development environment S32DS for Power 

Architecture 

Содержание SJA1105SMBEVM




































Отзывы:

Нет отзывов