manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Справочное руководство

Поделиться
Скачать
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Скачать руководство пользователя страница 917

Chapter 36 Nexus Development Interface (NDI)

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

917

 

36.12.6 Access to Debug Resources

Resources contained in the e200z0h OnCE Module which do not require the e200z0h processor core to be 
halted for access may be accessed while the e200z0h core is running, and will not interfere with processor 
execution. Accesses to other resources such as the CPUSCR require the e200z0h core to be placed in 
debug mode to avoid synchronization hazards. Debug firmware may ensure that it is safe to access these 
resources by determining the state of the e200z0h core prior to access. Note that a scan operation to update 
the CPUSCR is required prior to exiting debug mode if debug mode has been entered.

Some cases of write accesses other than accesses to the OnCE Command and Control registers, or the 
EDM bit of DBCR0 require the e200z0h 

m_clk

 to be running for proper operation. The OnCE control 

register provides a means of signaling this need to a system level clock control module.

In addition, since the CPU may cause multiple bits of certain registers to change state, reads of certain 
registers while the CPU is running (DBSR, etc.) may not have consistent bit settings unless read twice with 
the same value indicated. In order to guarantee that the contents are consistent, the CPU should be placed 
into debug mode, or multiple reads should be performed until consistent values have been obtained on 
consecutive reads.

29

WKUP

Wakeup Request Bit (WKUP) 
This control bit may be used to force the e200z0h 

p_wakeup

 output signal to be asserted. 

This control function may be used by debug firmware to request that the chip-level clock 
controller restore the 

m_clk

 input to normal operation regardless of whether the CPU is in a 

low power state to ensure that debug resources may be properly accessed by external 
hardware through scan sequences.

30

FDB

Force Breakpoint Debug Mode Bit (FDB) 
This control bit is used to determine whether the processor is operating in breakpoint debug 
enable mode or not. The processor may be placed in breakpoint debug enable mode by 
setting this bit. In breakpoint debug enable mode, execution of the ‘

bkpt

’ pseudo-instruction 

will cause the processor to enter debug mode, as if the 

jd_de_b

 input had been asserted. 

This bit is qualified with DBCR0

EDM

, which must be set for FDB to take effect.

31

DR

CPU Debug Request Control Bit
This control bit is used to unconditionally request the CPU to enter the Debug Mode. The 
CPU will indicate that Debug Mode has been entered via the data scanned out in the shift-IR 
state.
0 – No Debug Mode request
1 – Unconditional Debug Mode request
When the DR bit is set the processor will enter Debug mode at the next instruction boundary.

1

Unused by Z0Hn2p

Table 36-13. OnCE Control Register Bit Definitions (continued)

Bit(s)

Name

Description

Содержание SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды