manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Справочное руководство

Поделиться
Скачать
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Скачать руководство пользователя страница 311

Chapter 17 Flash Memory

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

311

 

Next, consider the memory map associated with the control and configuration registers.

There are multiple registers that control operation of the platform Flash controller. Note the first two Flash 
array registers (PFCR0, PFCR1) are reset to a device-defined value, while the remaining register (PFAPR) 
is loaded at reset from specific locations in the array’s shadow region.

Regardless of the number of populated banks or the number of Flash arrays included in a given bank, the 
configuration of the platform Flash controller is wholly specified by the platform Flash controller control 
registers associated with code Flash array0. The code array0 register settings define the operating behavior 
of 

both

 Flash banks. It is recommended to set the platform Flash controller control registers for both arrays 

to the array0 values.

NOTE

To perform program and erase operations, the control registers in the actual 
referenced Flash array must both be programmed, but the configuration of 
the platform Flash controller module is defined by the platform Flash 
controller control registers of code array0.

The 32-bit memory map for the platform Flash controller control registers is shown in 

Table 17-2

.

17.2.5

Functional description

The platform Flash controller interfaces between the AHB-Lite 2.v6 system bus and the Flash memory 
arrays.

The platform Flash controller generates read and write enables, the Flash array address, write size, and 
write data as inputs to the Flash array. The platform Flash controller captures read data from the Flash array 
interface and drives it onto the AHB. As much as four pages of data (128-bit width) from bank0 are 
buffered by the platform Flash controller. Lines may be prefetched in advance of being requested by the 
AHB interface, allowing single-cycle (0 AHB wait states) read data responses on buffer hits.

Several prefetch control algorithms are available for controlling page read buffer fills. Prefetch triggering 
may be restricted to instruction accesses only, data accesses only, or may be unrestricted. Prefetch 
triggering may also be controlled on a per-master basis. 

Buffers may also be selectively enabled or disabled for allocation by instruction and data prefetch.

Access protections may be applied on a per-master basis for both reads and writes to support security and 
privilege mechanisms.

Table 17-2. Platform Flash controller 32-bit memory map

Offset from

PFlash_BASE

(0xFFE8_8000)

Register

Location

0x001C

Platform Flash Configuration Register 0 (PFCR0)

on page 351

0x0020

Platform Flash Configuration Register 1 (PFCR1)

on page 354

 0x0024

Platform Flash Access Protection Register (PFAPR)

on page 356

Содержание SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды