manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE FRDMGD3162HBIEVM, Руководство пользователя, Страница: 8 / 43

Поделиться
Скачать
NXP Semiconductors SAFE ASSURE FRDMGD3162HBIEVM Скачать руководство пользователя страница 8

NXP Semiconductors

UM11729

FRDMGD3162HBIEVM half-bridge evaluation board

Figure 3. Evaluation board voltage and interface domains

Pin

Name

Function

1

AOUTL

analog output duty cycle encoded signal (low side) for reading temperature via

TSENSEA or voltage via AMUXIN

2

GS_ENH

gate strength enable HIGH; gate drive pull-up strength control logic

3

CSBL

chip select bar (low side)

4

GS_ENL

gate strength enable LOW; gate drive pull-down strength control logic

5

PWML

pulse width modulation (PWM) input (low side)

6

INTBL

interrupt bar (low side)

7

MOSIL

master out slave in (low side)

8

SCLK

serial clock input

9

MISOL

master in slave out (low side)

10

EN_PS

MCU control of flyback power supply

11

FSSTATEL

fail-safe state (low side)

12

GND

ground

13

FSENB

fail-safe enable (high side and low side)

14

MISOH

master in slave out (high side)

Table 2. Low-voltage domain 24-pin connector definitions

UM11729

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2022. All rights reserved.

User manual

Rev. 1 — 21 February 2022

8 / 43

Содержание SAFE ASSURE FRDMGD3162HBIEVM












































Отзывы:

Нет отзывов