manualshive.com logo in svg

NXP Semiconductors QorIQ T1040, Руководство пользователя, Страница: 63 / 68

Поделиться
Скачать
NXP Semiconductors QorIQ T1040 Скачать руководство пользователя страница 63

NOTE

For more information about building U-Boot images,
generating PBL images, see 

eSPI/SD/NAND boot

 in SDK

documentation.

4.6.4 Flashing SD card boot images

The steps for flashing and updating images for SD card are as follows:

You need to write two images, the first is the 

PBL1.bin

 produced by QCS tool, the second

is the 

u-boot.bin

.

1. Write 

PBL1.bin

 at offset block 8:

=>tftp 100000 PBL1.bin

=>mmcinfo

=>mmc write 100000 8 block_number 

2. Write u-boot.bin at offset 0x41000 (260KB), for example, 520(0x208) blockes.

=>tftp 100000 u-boot.bin

=>mmc write 100000 208 block_number

3. Write FMan microcode to SD card from block 0x820:

=>tftp 100000 fsl_fman_ucode_xx.bin

=>mmc write 100000 820 block_number 

4. Shut down the board.
5. Change board switch configuration for SD boot.
6. Switch on the board.

NOTE

For more information about building U-Boot images,
generating PBL images, see 

eSPI/SD/NAND boot

 in SDK

documentation.

4.6.5 Booting Linux

• Setting bootargs and serverip at U-Boot prompt:

                =>    setenv bootargs "root=/dev/ram rw console=ttyS0,115200 

ramdisk_size=700000”   

                =>    setenv ethact  FM1@DTSEC4

                =>    setenv ipaddr  <ipaddr>

                =>    setenv serverip <serverip>

                

• From U-Boot prompt, for booting Linux with 32-bit configuration on T1040RDB:

                =>    setenv my_kern 'tftp 0x1000000  <uImage>’   

                =>    setenv my_fs 'tftp 0x2000000  <rfs_e5500.bin>'

Chapter 4 Software configuration

QorIQ T1040 Reference Design Board User Guide, Rev. 0, 06/2015

Freescale Semiconductor, Inc.

63

Содержание QorIQ T1040





































































Отзывы:

Нет отзывов