manualshive.com logo in svg

NXP Semiconductors QorIQ T1040, Руководство пользователя, Страница: 60 / 68

Поделиться
Скачать
NXP Semiconductors QorIQ T1040 Скачать руководство пользователя страница 60

For a detailed switch default description, see 

Table 2-12

4.5 SDK Build details

For information on build details, see the SDK documentation.

4.6 Flashing and updating images

This section explains:

•

Flashing images on NOR flash and booting from NOR Flash

•

Flashing eSPI boot images

•

Booting Linux

4.6.1 Flashing images on and booting from NOR flash

Onboard Images can be updated as mentioned below. On board re-start, the board should
boot with new images. For information about switch settings, see 

Switch settings

• RCW programming on current bank (from U-Boot prompt)

For T1040RDB, use rcw/t1040rdb/RR_P_66/ rcw_1400MHz.bin

NOTE

This RCW can change depending upon the requirements

                =>    tftp 1000000 <rcw>.bin  

                =>    protect off all

                =>    erase 0xe8000000 0xe801ffff

                =>    cp.b 0x1000000 0xe8000000 $filesize

                

• FMan microcode programming on current bank (from U-Boot prompt)

                => tftp 0x3000000 <fsl_fman_ucode>.bin

                => protect off all

                Un-Protect Flash Bank # 1

                => erase 0xEFF00000 eff1ffff

                

                . done

                Erased 1 sectors

                => cp.b 3000000 0xEFF00000 10000

                Copy to Flash... 

                9....8....7....6....5....4....3....2....1....done

                

• U-Boot binary programming on current bank (from U-Boot prompt)

                => tftp 0x1000000 u-boot.bin

SDK Build details

QorIQ T1040 Reference Design Board User Guide, Rev. 0, 06/2015

60

Freescale Semiconductor, Inc.

Содержание QorIQ T1040





































































Отзывы:

Нет отзывов