NXP Semiconductors QorIQ T1040 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 68

NXP Semiconductors QorIQ T1040 Скачать руководство пользователя страница 38

The T1040 has a thermal diode attached to the die, allowing direct temperature
measurement. These pins are connected to an ADT7461 2-channel thermal monitor,
which allows direct reading of the temperature of the die and is accurate to ±1° C. The
second channel of the ADT7461 measures the ambient (board) temperature. The
ADT7461 temperature warning and alarm signals are connected to the CPLD for
monitoring. The CPLD or user software may use these signals to adjust CPU FAN speed
to protect the CPU from over-temperature failure.

I

2

C Bus

T1040

TEMP_ANODE

Thermal sensor

(ADT7461)

DXP1

DXN

TEMP_CATHODE

THERM

ALERT/THERM2

OVER ALARM

THERM ALARM

CPLD

PWM

FAN_Power

Figure 2-20. Thermal Sensor connection

2.19 DIP switch definition

The T1040RDB card has user selectable switches, for evaluating different boot
configurations and other special configurations for this device. The CPLD allows
software to override the configuration pins; for example, when the board is in a board
farm. In order to use the CPLD override option, software sets an override bit that allows
the CPLD to override the switch setting during reset.

DIP switch definition

QorIQ T1040 Reference Design Board User Guide, Rev. 0, 06/2015

38

Freescale Semiconductor, Inc.

«
...
36
37
38
39
40
...
»

Содержание QorIQ T1040





































































Отзывы:

Нет отзывов