NXP Semiconductors QorIQ LS1028A Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 112

NXP Semiconductors QorIQ LS1028A Скачать руководство пользователя страница 33

UART1_SIN,

UART1_SOUT,

RS232

XCVR

LTC2804-1

UART1

(bottom)

UART2

(top)

LS1028A

UART2_SIN,

UART2_SOUT,

NORCOMP

178-009-613R571

or equiv

Dual-stack DB9male

MUX

NX3DV221TK

To mikro-click

modules

from CPLD

CFG_MUX_UART2_SE L0

OVDD

(1.8V)

1

0

Figure 14. DUART architecture

The UART2 signals can be used either to communicate with mikro-click modules or with RS232-compliant devices using the
LTC2804-1 transceiver. The selection is done through a mux which is controlled through the CFG_MUX_UART2_SEL0 signal by
CPLD.

Table 14. UART configuration and setup

Configuration signal

Config register

DIP switch

Description

CFG_MUX_UART2_SEL0

BRDCFG3[5:4]

SW2[5:6]

• 0x: UART2 on DB9

connector (default value)

• 10: UART2 on mikro-click

module 1

• 11: UART2 on mikro-click

module 2

2.12 CAN interface

The LS1028A processor supports two controller area network (CAN) modules, CAN1 and CAN2. On the LS1028ARDB, the CAN
ports are available for external connection through a dual-port stacked DB9 male connector. Two high-speed CAN transceivers
TJA1051T/3 from NXP (U54 and U56) provide an interface for the CAN ports to send and receive CAN signals to and from the
processor. The TJA1052T/3 transceivers can support data rate of up to 5 Mbit/s in CAN with Flexible Data-Rate (CAN FD) phase.

The figure below shows the CAN architecture.

CAN interface

QorIQ LS1028A Reference Design Board Reference Manual, Rev. b, 11/2018

NXP Semiconductors

COMPANY CONFIDENTIAL

33

«
...
31
32
33
34
35
...
»

Содержание QorIQ LS1028A

















































































































Отзывы:

Нет отзывов