NXP Semiconductors PXN2020 Скачать руководство пользователя страница 506 | Manualshive

Страница: 506 / 1376

NXP Semiconductors PXN2020 Скачать руководство пользователя страница 506

DMA Channel Multiplexer (DMA_MUX)

PXN20 Microcontroller Reference Manual, Rev. 1

23-2

Freescale Semiconductor

23.1.2

Features

The DMA_MUX has these major features:

•

32 independently selectable DMA channel routers

— Four channels with normal or periodic triggering capability

— 24 channels with normal operation only

— Each channel router can be assigned to 1 of 55 possible peripheral DMA sources, eight always

enabled sources, or one always disabled source.

23.1.3

Modes of Operation

DMA channels 0–7 may be used in the following modes, but channels 8–31 may only be configured to
disabled or normal mode.

•

Disabled mode

In this mode, the DMA channel is disabled. Because disabling and enabling of DMA channels is
done primarily via the DMA registers, this mode is used mainly as the reset state for a DMA
channel in the DMA channel mux. It may also be used to temporarily suspend a DMA channel
while reconfiguration of the system takes place (changing the period of a DMA trigger, for
example).

•

Normal mode

In this mode, a DMA source (such as SCI transmit or SCI receive for example) is routed directly
to the specified DMA channel. The operation of the DMA_MUX in this mode is completely
transparent to the system.

•

Periodic trigger mode

In this mode, a DMA source may only request a DMA transfer (such as when a transmit buffer
becomes empty or a receive buffer becomes full) periodically. Configuration of the period is done
in the registers of the periodic interrupt timer.

23.2

External Signal Description

The DMA_MUX has no external signals.

23.3

Memory Map and Registers

This section provides a detailed description of all DMA_MUX registers.

23.3.1

Module Memory Map

The DMA_MUX memory map is shown in

. The address of each register is given as an offset

to the DMA_MUX base address. Registers are listed in address order, identified by complete name and
mnemonic, and list the type of accesses allowed.

All registers are accessible via 8-bit, 16-bit, or 32-bit accesses. However, 16-bit accesses must be aligned
to 16-bit boundaries and 32-bit accesses must be aligned to 32-bit boundaries. As an example,

«
...
504
505
506
507
508
...
»

Содержание PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов