NXP Semiconductors P4080 Скачать руководство пользователя страница 48

Страница: 48 / 60

P4080 Development System User’s Guide, Rev. 0

Freescale Semiconductor

Programming Model

7.1.4

General Control/Status Register (PX_CSR)

The general control/status register (PX_CSR) contains various control and status fields, as described
below.

7.1.5

Reset Control Register (PX_RST)

The reset control register (PX_RST) may be used to reset the system, or portions of it.

Offset 0x03

Access: Read/Write

EVESRC

EVEDEST

LED

FAIL

Reset

Figure 29. General Control/Status Register (PX_CSR)

Table 26. PX_CSR Field Descriptions

Bits

Name

Description

0–2

EVESRC

Selects one of several inputs for mapping to internal signal

esig, which in turn may be connected to

special outputs (see PIX_CSR[EVEDEST]).
000 esig <- event_b
001 esig <- trig_out
010 esig <- evt_b(2)
011 esig <- evt_b(3)
111 esig <- chkstpi_b

3–5

EVEDEST

Selects the output pin to which the internal signal

esig is driven (see PIX_CSR[EVESRC] for details).

001 esig -> trig_in
010 esig -> evt_b(7)
011 esig -> evt_b(8)
100 esig -> evt_b(9)

LED

If set, the diagnostic LEDs are driven by the value in the PX_LED register; otherwise, the LEDs
default to activity monitors

FAIL

If set, the external LED labeled “FAIL” is turned on and the one labeled “PASS” is off; otherwise, if
cleared, the opposite is true.

Offset 0x04

Access: Read/Write

ALL

—

SXSLOT

PHY

—

GEN

Reset

All ones

Figure 30. Reset Control Register (PX_RST)

Содержание P4080





























































Результаты поиска

Содержание P4080

Отзывы:

NXP Semiconductors P4080, Руководство пользователя, Страница: 48 / 60

Результаты поиска

Содержание P4080

Отзывы: