manualshive.com logo in svg

NXP Semiconductors MSC8113, Справочное руководство

NXP Semiconductors MSC8113 - процессор высокой производительности для широкого спектра приложений. Пользователи могут бесплатно загрузить полное руководство по использованию (Reference Manual) с нашего веб-сайта. Получите доступ к этой информативной инструкции прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

MSC8113 Reference Manual, Rev. 0

20-34

Freescale Semiconductor

TDM Interface

The received data is stored in 256 entries of 8 bytes each located in the addresses between 
0x0000–0x07FF. This memory contains 1, 2, 4, 8, 16, or 32 indexed buffers, starting at 0. 
Each buffer contains multiple frames. The number of buffers used to store the received 
data is indicated in the RNB field of the TDMx Receive number of Buffers Register 
(TDMxRNB) (see page 20-64). Channel C in buffer B is the 8 bytes starting at 
(256 / (RNB + 1) 

×

  B + C) 

×

 8. (Refer to Section 20.2.3, TDM Data Structures, on 

page 20-13 for details)

4.

Fill the sync data in all the TDM transmit local memory. 

Transmit data is located in the TDM local memory before it is transmitted externally. The 
data is stored in 256 8-byte entries in addresses between 0x1800–0x1FFF. This memory 
can contain 1, 2, 4, 8, 16, or 32 indexed buffers starting at 0. Each buffer contains multiple 
frames. The number of buffers used to store the transmitted data is indicated in the TNB 
field of the TDMx Transmitter Number of Buffers Register (TDMxTNB). Channel C in 
buffer B is the 8 bytes starting at (256/(TNB+1) 

×

 B+C) 

× 

8. 

5.

Clear the TDMxRER and TDMxTER event registers by writing a value of 0xF to each 
of them.

6.

Set the TDMxRCR[REN] bit and/or the TDMxTCR[TEN] bit.

20.7

TDM Programming Model

The handshake between the TDM module and the SC140 core occurs via a set of registers, data 
structures in the memory, and interrupts. All TDM registers are mapped into the IPBus address 
space. See Chapter 8, Memory Map for details on IPBus addressing. There are four modules 
(TDM 0–3), each with its own region in the IPBus address space. Within the module address 
space, the area is divided into spaces for configuration registers, control registers, and status 
registers as follows:

„

Configuration registers. Set the operation modes and provide indications for all channels. 
They are set before the TDM is enabled and should not be changed while the TDM is 
active.

„

Control registers. Set the channel specific parameters individually for each channel and 
the threshold pointers. These registers can be changed during operation. 

„

Status registers. Read-only registers that can be accessed any time.

This section describes the TDM module registers, which are listed as follows:

„

TDMx General Interface Register (TDMxGIR), page 20-36.

„

TDMx Receive Interface Register (TDMxRIR), page 20-43.

„

TDMx Transmit Interface Register (TDMxTIR), page 20-45.

„

TDMx Receive Frame Parameters (TDMxRFP), page 20-47.

„

TDMx Transmit Frame Parameters (TDMxTFP), page 20-49.

Содержание MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8113

TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Бренд: TE Connectivity Страницы: 236
Renesas Asynchronous SH7145F Application Note preview
Asynchronous SH7145F
Бренд: Renesas Страницы: 17
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Бренд: ADC Страницы: 7
Fracarro FRPRO EVO HD Quick Start Manual preview
FRPRO EVO HD
Бренд: Fracarro Страницы: 12
Multitech MultiConnect SE MTS2EA Specification Sheet preview
MultiConnect SE MTS2EA
Бренд: Multitech Страницы: 2
D3 DesignCore RVP-TDA3 Series Quick Start Manual preview
DesignCore RVP-TDA3 Series
Бренд: D3 Страницы: 34
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Бренд: QNAP Страницы: 51
Longshine LCS-8170 User Manual preview
LCS-8170
Бренд: Longshine Страницы: 35
Mitsubishi M16C/20 Series Software Manual preview
M16C/20 Series
Бренд: Mitsubishi Страницы: 188
ZALMAN CNPS9800 MAX User Manual preview
CNPS9800 MAX
Бренд: ZALMAN Страницы: 32
Variscite VAR-SOM-MX6 HEAT PLATE KIT Quick Start Manual preview
VAR-SOM-MX6 HEAT PLATE KIT
Бренд: Variscite Страницы: 3
FDI USB-ICP-SAB9 Quick Start Manual preview
USB-ICP-SAB9
Бренд: FDI Страницы: 15
G&D ControlCenter-IP 2.0 Installation Manual preview
ControlCenter-IP 2.0
Бренд: G&D Страницы: 60
ADTRAN 1181413L2 Installation And Maintenance Manual preview
1181413L2
Бренд: ADTRAN Страницы: 100
ABB COM600 series 5.1 User Manual preview
COM600 series 5.1
Бренд: ABB Страницы: 42
Huawei E5785-320a Product Description preview
E5785-320a
Бренд: Huawei Страницы: 23
Huawei eAN3810A Hardware Installation Manual preview
eAN3810A
Бренд: Huawei Страницы: 50
Huawei CX600-X1-M Series Hardware Description preview
CX600-X1-M Series
Бренд: Huawei Страницы: 234

Бренды по названию

Популярные бренды

Загрузить еще бренды