manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 539

Universal Serial Bus Interface

MCF5253 Reference Manual, Rev. 1

Freescale Semiconductor

24-77

 

will automatically execute the value of Mult transactions. The host controller will not execute all Mult 
transactions if:

•

The endpoint is an OUT and Transaction 

n

 Length goes to zero before all the Mult transactions 

have executed (ran out of data), or

•

The endpoint is an IN and the endpoint delivers a short packet, or an error occurs on a transaction 
before Mult transactions have been executed. The end of micro-frame may occur before all of the 
transaction opportunities have been executed. When this happens, the transfer state of the transfer 
description is advanced to reflect the progress that was made, the result written back to the iTD and 
the host controller proceeds to processing the next micro-frame.

24.9.8.2

Software Operational Model for iTDs

A client buffer request to an isochronous endpoint may span 1 to N micro-frames. When N is larger than 
one, the system software may have to use multiple iTDs to read or write data with the buffer (if N is larger 
than eight, it must use more than one iTD).

Figure 24-48

 illustrates the simple model of how a client buffer is mapped by the system software to the 

periodic schedule (that is, the periodic frame list and a set of iTDs). On the right is the client description 
of its request. The description includes a buffer base address plus additional annotations to identify which 
portions of the buffer should be used with each bus transaction. In the middle is the iTD data structures 
used by the system software to service the client request. Each iTD can be initialized to service up to 24 
transactions, organized into eight groups of up to three transactions each. Each group maps to one 
micro-frame's worth of transactions. The EHCI controller does not provide per-transaction results within 
a micro-frame. It treats the per-micro-frame transactions as a single logical transfer. On the left is the host 
controller’s frame list. The system software establishes references from the appropriate locations in the 
frame list to each of the appropriate iTDs. If the buffer is large, then the system software can use a small 
set of iTDs to service the entire buffer. The system software can activate the transaction description records 
(contained in each iTD) in any pattern required for the particular data stream.

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды