manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство, Страница: 438 / 648

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 438

Advanced Technology Attachment Controller (ATA)

MCF5253 Reference Manual, Rev. 1

23-12

Freescale Semiconductor

 

23.4.3.5

UDMA Out Timing Diagrams

UDMA mode timing is more complicated than PIO mode or MDMA mode. In this section, timing 
diagrams for UDMA out are provided.

Figure 23-9

 shows timing for UDMA out transfer start.

Table 23-6. Timing Parameters for UDMA in Burst

ATA

Parameter

Spec

Parameter

Value

Required Conditions

tack

tack

tack(min) = (time_ack * T) - ( tskew2)

time_ack

tenv

tenv

tenv(min) = (time_env * T) - ( tskew2)

tenv(max) = (time_env * T) + ( tskew2)

time_env

tds

tds1

tds - (tskew3) - ti_ds > 0

tskew3, ti_ds, ti_dh 

should be low enough

tdh

tdh1

tdh - (tskew3) -ti_dh > 0

tcyc

tc1

(tcyc - tskew + TBD) > T

T big enough

trp

trp

trp(min) = time_rp * T - ( tskew6)

time_rp

–

tx1

1

1

There is a special timing requirement in the ATA host that requires the internal DIOW to go only high three clocks after the last 
active edge on the DSTROBE signal. The equation given on this line tries to capture this constraint.

2. Make ton and toff big enough to avoid bus contention.

(time_rp * T) - (tco + tsu + 3T + 2 *tbuf + 2*tcable2) > trfs (drive)

time_rp

tmli

tmli1

tmli1(min) = (tim 0.4) * T 

time_mlix

tzah

tzah

tzah(min) = (ti 0.4) * T 

time_zah

tdzfs

tdzfs

tdzfs = (time_dzfs * T) - ( tskew2)

time_dzfs

tcvh

tcvh

tcvh = (time_cvh *T) - ( tskew2)

time_cvh

–

ton
toff

ton = time_on * T - tskew1
toff = time_off * T - tskew1

–

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов