manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MC9S08PA4 Скачать руководство пользователя страница 39

3.2.4 Active BDM enabled in stop3 mode

Entry into the active background mode from run mode is enabled if the
BDC_SCR[ENBDM] bit is set. This register is described in the 

development support

. If

BDC_SCR[ENBDM] is set when the CPU executes a STOP instruction, the system
clocks to the background debug logic remain active when the MCU enters stop mode, so
background debug communication is still possible. In addition, the voltage regulator does
not enter its low-power standby state but maintains full internal regulation.

Most background commands are not available in stop mode. The memory-access-with-
status commands do not allow memory access, but they report an error indicating that the
MCU is in either stop or wait mode. The BACKGROUND command can be used to
wake the MCU from stop and enter active background mode if the BDC_SCR[ENBDM]
bit is set. After entering background debug mode, all background commands are
available.

3.2.5 LVD enabled in stop mode

The LVD system is capable of generating either an interrupt or a reset when the supply
voltage drops below the LVD voltage. If the LVD is enabled in stop (LVDE and LVDSE
bits in SPMSC1 both set) at the time the CPU executes a STOP instruction, then the
voltage regulator remains active during stop3 mode.

3.2.6 Power modes behaviors

Executing the WAIT or STOP command puts the MCU in a low power consumption
mode for standby situations. The system integration module (SIM) holds the CPU in a
non-clocked state. The operation of each of these modes is described in the following
subsections. Both STOP and WAIT clear the interrupt mask (I) in the condition code
register, allowing interrupt to occur. The following table shows the low power mode
behaviors.

Table 3-1. Low power mode behavior

Mode

Run

Wait

Stop3

PMC

Full regulation

Full regulation

Loose regulation

ICS

On

On

Optional on

OSC

On

On

Optional on

LPO

On

On

On

CPU

On

Standby

Standby

FLASH

On

On

Standby

Table continues on the next page...

Chapter 3 Power management

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

NXP Semiconductors

39

Содержание MC9S08PA4


















































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды